65-70 Full Size Power Train Tech Forum

SGS Welding · SGS Welding

Car is 1967 Parisienne convertible I need to order a new vent complete with new grommet. Where do I find one of these? I am hoping someone in our club knows from first hand knowledge the right one to order? In case it matters the car came factory with a 327 Powerglide. Thanks

4SPEED427 · 4SPEED427

Does anyone have a driveshaft from a 66 Pontiac or full size Chev, Powerglide car or 3 speed standard, lying on the floor that they can tell me the measurement from centre of U joint cup to centre of U joint cup? I know, silly request from me when I have one in the garage on my car but I can't put it up on the hois...

4SPEED427 · 4SPEED427

I found this online for a 1965 Impala driveshaft. I'm sure 66 will be the same. Can someone confirm this?? (Excludes TH400 which is shorter)

Hobbes · Hobbes

Hi, I am swapping a minty Parisienne dashboard into my stratochief, I have to swap the speedometer assembly over. I am assuming it is pretty straightforward. But while I am there my odometer isnt working. I saw a thread a while ago about fixing that. If anybody could send me the link I couldnt seem to fin...

65 SD L79 · 65 SD L79

427 BBC T Handle Shifter Knob Aluminum Corvette Impala Camaro Copo SS RS Hurst | eBay

4SPEED427 · 4SPEED427

Anyone here bought one of the kits and rebuilt their own water pump so that they can keep their original correct casting number and date?

4SPEED427 · 4SPEED427

I am cleaning stuff in my tumbler and when I was putting this one in the tumbler today I noticed it doesn't have a seal in it. I never realized not all of these were the same design. There are some with a seal inside to keep the oil from coming out past the gear. To me, this design would be more prone to oil leaks...

ABC123 · ABC123

I have been looking in all the boxes Howmac sent me. So far, I have not come accross a distributor and rotor shaft. Are big block and small block common ? This one is set up with MSD Ignition. -- Edited by ABC123 on Saturday 22nd of October 2022 04:10:27 PM

cdnpont · cdnpont

A nice upgrade just landed in my driveway after a long journey from Manitoba and via London Ontario. Thanks a ton needs to go out to Carl and Randy! Thanks so much guys! It's a complete, ready to run open 3.07 12 bolt from Carl's 66 Strato. While my leaky 3.08 10 bolt seems to work fine, it's a sloppy 3 leg, an...

oshawacliff · oshawacliff

my 67 impala instrument cluster was rebuilt many years ago. It seems that every year I have a noisy speedo cable. Pull it out and lube it but not perfect. The speedo needle has a minor fluctuation but settles down after a bit of lube. It seems to be a yearly ritual. The transmission is 3 speed th350. Any...

65 SD L79 · 65 SD L79

looked at a number of sites and see all kinds of different answers. 60 over I think all would say ok but what about 70, 80 or 100? what do you think about sleeving back to standard? This also has to do with saving an original 66-69 427 block

LT1Caddy · LT1Caddy

Hi.. Went for a drive on Friday, temperature was 85F +. Car runs at 180-200 F most of the time, cooler on the highway. But Friday the temp was up over 210F driving thru town. Might have got to 215F but I was back on the highway in a few minutes and she started to cool down to 190F. When I got home in the garage I l...

4SPEED427 · 4SPEED427

https://www.summitracing.com/parts/ado-d3968a Anyone ever heard of these, or had one? Kind of embarrassing who spanned 40 years in GM parts to admit he's never heard of these, but I've never heard of these. I was piddling around on the AC Delco site to see what all they had listed for my car and this...

65 SD L79 · 65 SD L79

I wanted to put a nice new shiny exhaust system on the 396 car so I ordered a system off eBay. I picked it up in Ohio on my way to the car show. After seeing it I figured I would use it on the L72 car -- Edited by 70 SS ACADIAN on Monday 8th of August 2022 08:27:53 PM

1965CS · 1965CS

Yet another incident that I cannot explain, hoping someone here can. Rocker tension seemed ok, can tell in the images that the nuts are not loose. Replaced the bent rods, replaced the rockers with roller type, then the other side did this:

gord · gord

Would anybody happen to know anything about these numbers on my 396 block? 3955272. P. Gm4. B25-9

LandShark68_2+2 · LandShark68_2+2

Hi guys, I recently installed a new carb on the 68 2+2 and I am wondering what this rubber hose is for, coming out of the bottom of the breather. Does it attach to the carb somewhere or does it just dangle ? Regards, Scott (LandShark ...)

koolconvertible · koolconvertible

Hi all, so the F40 RPO all our aussie cars got is for heavy duty front and rear suspension. I know that means 4 link and possible shockie ratings but what is the difference for front suspension over standard? Just shockie ratings? cheers all.

4SPEED427 · 4SPEED427

https://www.ebay.com/itm/1965-1966-1967-1968-1969-1970-Chevy-Impala-Bel-Air-Caprice-Biscayne-Radiator/291519...

Hobbes · Hobbes

Hi ponchonians, just checking to see if someone knows what these symptoms might be, I have 1965 stratochief with the straight 6/250 one barrel. upon accelerating it started to stumble the engine sounds like its running fine but has a definite stumble in it It seems to be becoming more pronounced, It s...

Topic		Started By	Replies	Views	Last Post
	Gas tank vent and grommet (Preview) Car is 1967 Parisienne convertible I need to order a new vent complete with new grommet. Where do I find one of these? I am hoping someone in our club knows from first hand knowledge the right one to order? In case it matters the car came factory with a 327 Powerglide. Thanks	SGS Welding	10	773	Apr 17, 2023 by LT1Caddy
	1966 Powerglide driveshaft length (Preview) Does anyone have a driveshaft from a 66 Pontiac or full size Chev, Powerglide car or 3 speed standard, lying on the floor that they can tell me the measurement from centre of U joint cup to centre of U joint cup? I know, silly request from me when I have one in the garage on my car but I can't put it up on the hois...	4SPEED427	4	659	Apr 17, 2023 by 4SPEED427
	Driveshaft length (Preview) I found this online for a 1965 Impala driveshaft. I'm sure 66 will be the same. Can someone confirm this?? (Excludes TH400 which is shorter)	4SPEED427	3	814	Apr 7, 2023 by 4SPEED427
	1965 Speedo assembly swap (Preview) Hi, I am swapping a minty Parisienne dashboard into my stratochief, I have to swap the speedometer assembly over. I am assuming it is pretty straightforward. But while I am there my odometer isnt working. I saw a thread a while ago about fixing that. If anybody could send me the link I couldnt seem to fin...	Hobbes	4	1046	Mar 15, 2023 by Hobbes
	Carl? (Preview) 427 BBC T Handle Shifter Knob Aluminum Corvette Impala Camaro Copo SS RS Hurst \| eBay	65 SD L79	3	1010	Jan 27, 2023 by LT1Caddy
	Has anyone done their own water pump rebuild? (Preview) Anyone here bought one of the kits and rebuilt their own water pump so that they can keep their original correct casting number and date?	4SPEED427	15	1418	Nov 14, 2022 by unruhjonny
	Speedometer gear sleeve/bullet (Preview) I am cleaning stuff in my tumbler and when I was putting this one in the tumbler today I noticed it doesn't have a seal in it. I never realized not all of these were the same design. There are some with a seal inside to keep the oil from coming out past the gear. To me, this design would be more prone to oil leaks...	4SPEED427	5	1133	Oct 30, 2022 by LT1Caddy

	Is the distributor Cap and Rotor shaft, common in a 1969 small block and big block ? (Preview) I have been looking in all the boxes Howmac sent me. So far, I have not come accross a distributor and rotor shaft. Are big block and small block common ? This one is set up with MSD Ignition. -- Edited by ABC123 on Saturday 22nd of October 2022 04:10:27 PM	ABC123	6	897	Oct 23, 2022 by seventy2plus2
	12 bolt upgrade for the 65 (Preview) A nice upgrade just landed in my driveway after a long journey from Manitoba and via London Ontario. Thanks a ton needs to go out to Carl and Randy! Thanks so much guys! It's a complete, ready to run open 3.07 12 bolt from Carl's 66 Strato. While my leaky 3.08 10 bolt seems to work fine, it's a sloppy 3 leg, an...	cdnpont	6	1238	Oct 2, 2022 by cdnpont
	Speedo cable replacement (Preview) my 67 impala instrument cluster was rebuilt many years ago. It seems that every year I have a noisy speedo cable. Pull it out and lube it but not perfect. The speedo needle has a minor fluctuation but settles down after a bit of lube. It seems to be a yearly ritual. The transmission is 3 speed th350. Any...	oshawacliff	1	966	Sep 2, 2022 by LT1Caddy
	how far would you bore a 427? (Preview) looked at a number of sites and see all kinds of different answers. 60 over I think all would say ok but what about 70, 80 or 100? what do you think about sleeving back to standard? This also has to do with saving an original 66-69 427 block	65 SD L79	8	1108	Sep 1, 2022 by Howmac
	Upper rad hose collapsed...!!!! (Preview) Hi.. Went for a drive on Friday, temperature was 85F +. Car runs at 180-200 F most of the time, cooler on the highway. But Friday the temp was up over 210F driving thru town. Might have got to 215F but I was back on the highway in a few minutes and she started to cool down to 190F. When I got home in the garage I l...	LT1Caddy	18	1426	Aug 23, 2022 by oshawacliff
	Delco electronic ignition conversion kit (Preview) https://www.summitracing.com/parts/ado-d3968a Anyone ever heard of these, or had one? Kind of embarrassing who spanned 40 years in GM parts to admit he's never heard of these, but I've never heard of these. I was piddling around on the AC Delco site to see what all they had listed for my car and this...	4SPEED427	11	1289	Aug 18, 2022 by unruhjonny
	66 B body exhaust system (Preview) I wanted to put a nice new shiny exhaust system on the 396 car so I ordered a system off eBay. I picked it up in Ohio on my way to the car show. After seeing it I figured I would use it on the L72 car -- Edited by 70 SS ACADIAN on Monday 8th of August 2022 08:27:53 PM	65 SD L79	15	1072	Aug 11, 2022 by Canadian Poncho

	Rocker-lifter issue (Preview) Yet another incident that I cannot explain, hoping someone here can. Rocker tension seemed ok, can tell in the images that the nuts are not loose. Replaced the bent rods, replaced the rockers with roller type, then the other side did this:	1965CS	12	1282	Jul 21, 2022 by 1965CS
	Motor (Preview) Would anybody happen to know anything about these numbers on my 396 block? 3955272. P. Gm4. B25-9	gord	4	926	Jul 20, 2022 by 694279
	What's this rubber hose for ? (Preview) Hi guys, I recently installed a new carb on the 68 2+2 and I am wondering what this rubber hose is for, coming out of the bottom of the breather. Does it attach to the carb somewhere or does it just dangle ? Regards, Scott (LandShark ...)	LandShark68_2+2	19	1389	Jul 20, 2022 by MC
	F40 heavy duty suspension RPO (Preview) Hi all, so the F40 RPO all our aussie cars got is for heavy duty front and rear suspension. I know that means 4 link and possible shockie ratings but what is the difference for front suspension over standard? Just shockie ratings? cheers all.	koolconvertible	16	1294	Jul 13, 2022 by Canadian Poncho
	Anyone use this aluminum radiator? ( 1 2 ) (Preview) https://www.ebay.com/itm/1965-1966-1967-1968-1969-1970-Chevy-Impala-Bel-Air-Caprice-Biscayne-Radiator/291519...	4SPEED427	27	3944	Jul 8, 2022 by 4SPEED427
	Stumble on acceleration ( 1 2 ) (Preview) Hi ponchonians, just checking to see if someone knows what these symptoms might be, I have 1965 stratochief with the straight 6/250 one barrel. upon accelerating it started to stumble the engine sounds like its running fine but has a definite stumble in it It seems to be becoming more pronounced, It s...	Hobbes	31	1833	Jul 4, 2022 by Hobbes
«First < 1 2 3 4 5 … 30 > Last» \| Page of 30 sorted by