65-70 Full Size Chassis Tech Forum

Leo2+2 · Leo2+2

I'm trying to remove the front bumper. The parking lights & housing go through a bracket that only so the wiring stays in place but the housing won't go through. I need to disconnect it. Any ideas where? 67 Parisienne.

68 Grande · 68 Grande

I have been researching a bit on upgrading my steering box to a 12.7 to 1 ratio for quicker handling responses on the 68 Grande. From what I find is that everyone that upgrades the box comments on the upgrade as being positive. My box is not leaking but it is the standard S Saginaw box with a 6 on it, four b...

Georges · Georges

1967 Pontiac

bradkerbick · bradkerbick

Hi everyone, is there a top and bottom side to the front springs? Mine dont have any white or yellow marks like I read in a post. They look symmetrical on both ends. I also read a post that said they can only fit in one way. It's on a 68 Parisienne. Thanks

Pearl · Pearl

Hello all! So I have a 1966 Parisienne, Canadian model, and have had it in the frame shop for some adjustments - passenger side was sagging and turns out it wasn't suspension as I thought before changing the springs. The guy who owns the shop, didn't have the exact frame measurement specs for my car, s...

cdnpont · cdnpont

Finally got around to installing the Viking hybrid coilovers I'd bought a while back. Breaking the front end apart on the B body is a job nobody enjoys, and I'd done it far too many times trying to find an optimum spring rate. Seems replacement springs are far too stiff these days, and it's rare anyone ca...

SGS Welding · SGS Welding

Can a faulty proportioning /combination valve screw up and only deliver part pressure to one front brake and not the other? Everything else is new and adjusted properly even the suspension has all new bushings ,ball joints everything. New flex lines,new wheel cylinders, both wheel cylinders seem...

koolconvertible · koolconvertible

so, anyone have a spare ram or two (might be nice to have a spare) to suit my 65 they are willing to post to australia? from experience can be a bit laborious doing the funds transfer....and prefer slow mail rather than fast priority as it gets expensive... one of mine has a nylon top and the thread is strip...

koolconvertible · koolconvertible

Hi all, do i have the pump mounted upside down? having trouble with diagrams too. Which outlet goes to pump top and bottom? Ta.

tramminc · tramminc

Could someone please measure from the center of each bolt hole and give me the total length. The problem is that I replaced the old ones with adjustables but lost the paper with the measurement.

RonchoPoncho · RonchoPoncho

Ok so what started out as front brakes on my 65 Parisienne has turned into bearings, seals etc. The problem I have is the seal and or gasket that should be at the front backing plate and spindle were badly worn. Any help identifying/finding these parts would be appreciated. The pic is of what I should hav...

cdnpont · cdnpont

I've had a rebuilt and replated booster on the shelf for years now, and since I'm about to replace the master, converting to a 1"bore from a 1 1/8", I'm thinking of using it as it looks so nice compared to the original one (which currently works perfect anyway, just ugly). Is it a big job to replace the boos...

hutch400 · hutch400

Picked this old brake lathe up a couple of years ago from a family friend who was getting rid of it. Cleaned her all up and repainted it (why not right?) and finally have it all set up. Turned the drums on the 65, and they came out great! Been a while since i've done this so i practiced on some old ones first lol...

jsr · jsr

Hey everybody ....i took my upper control arms off my 66 Bonneville to replace bushings and ball joints and clean and paint . ive got them mixed up and don't know which came of what side . They look exactly the same as each other and do not appear to have any offsets or anything to not allow them to be fitted o...

SGS Welding · SGS Welding

Hey guys I wonder if anyone knows the scoop on steering upgrades? I have limited knowledge First off my car is power steering and it works fine! I just want to learn about upgrades I have heard you can put Camaro guts in our boxes I have heard about a 605 I dont know what our cars have? An 800???? Can someo...

fptmelo · fptmelo

My Parisienne is leaving the shop and about to make his import trip from Venezuela to Brazil. It goes with a problem the Venezuelan mechanics couldn't fix. The car has front disc brakes, apparently adapted from a Chevy Caprice. This construction leads to a difficulty in aligning, and to an unsafe res...

4SPEED427 · 4SPEED427

Rather than totally derail the "New York Times"thread (yeah, I know, I'm usually the king of derailing....) I figured I'd ask the question in a new thread. Are you guys saying there that you think the stock wheels from a late 60's Canadian Pontiac are different than the same era Impala? (to...

4SPEED427 · 4SPEED427

My Strato Chief turned 51 in May. It has 42,000 miles. It was up on the hoist the last while and when I walked by the other day, I noticed a puddle under the driver's front wheel. It appears my original shock absorber decided to leak out at such a young age and so few miles... Someone told me there is a company...

cdnpont · cdnpont

Team, Has anyone used rear spring spacers on their 65-70 B Bodies? I have what I feel is the perfect rate in the rear, but unfortunately they have sagged a little since new. I'd like to put in another inch or so of lift, but I'm not going through the hassle of doing another set of springs. And air shocks are...

cdnpont · cdnpont

I'm making new tranny lines for the project, so it'll have to be done just before dropping it in, when I get the trans attached to the motor. The old lines are going away with the 350 motor and TH400. I have steel 5/16 line, and man is the stuff ever hard! I can hardly bend it at all by hand, and the bending...

Topic		Started By	Replies	Views	Last Post
	How do you disconnect parking lights? (Preview) I'm trying to remove the front bumper. The parking lights & housing go through a bracket that only so the wiring stays in place but the housing won't go through. I need to disconnect it. Any ideas where? 67 Parisienne.	Leo2+2	1	1258	Oct 30, 2018 by Leo2+2
	Steering gear (box) rebuilder in Manitoba? (Preview) I have been researching a bit on upgrading my steering box to a 12.7 to 1 ratio for quicker handling responses on the 68 Grande. From what I find is that everyone that upgrades the box comments on the upgrade as being positive. My box is not leaking but it is the standard S Saginaw box with a 6 on it, four b...	68 Grande	15	2316	Oct 26, 2018 by seventy2plus2
	Anyone interested in a 1967 Parisienne convertible project? (Preview) 1967 Pontiac	Georges	9	1701	Oct 15, 2018 by Georges
	Front spring orientation (Preview) Hi everyone, is there a top and bottom side to the front springs? Mine dont have any white or yellow marks like I read in a post. They look symmetrical on both ends. I also read a post that said they can only fit in one way. It's on a 68 Parisienne. Thanks	bradkerbick	11	1718	Sep 29, 2018 by bradkerbick
	Frame spec's (Preview) Hello all! So I have a 1966 Parisienne, Canadian model, and have had it in the frame shop for some adjustments - passenger side was sagging and turns out it wasn't suspension as I thought before changing the springs. The guy who owns the shop, didn't have the exact frame measurement specs for my car, s...	Pearl	3	1334	Aug 25, 2018 by Pearl
	Installed Viking Hybrid Coilovers in the Grande. (Preview) Finally got around to installing the Viking hybrid coilovers I'd bought a while back. Breaking the front end apart on the B body is a job nobody enjoys, and I'd done it far too many times trying to find an optimum spring rate. Seems replacement springs are far too stiff these days, and it's rare anyone ca...	cdnpont	10	4655	Aug 21, 2018 by cdnpont
	67 Parisienne brake pull (Preview) Can a faulty proportioning /combination valve screw up and only deliver part pressure to one front brake and not the other? Everything else is new and adjusted properly even the suspension has all new bushings ,ball joints everything. New flex lines,new wheel cylinders, both wheel cylinders seem...	SGS Welding	12	2683	Jul 12, 2018 by 4SPEED427
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
	WANTED! Convertible top ram. (Preview) so, anyone have a spare ram or two (might be nice to have a spare) to suit my 65 they are willing to post to australia? from experience can be a bit laborious doing the funds transfer....and prefer slow mail rather than fast priority as it gets expensive... one of mine has a nylon top and the thread is strip...	koolconvertible	9	1667	Jun 23, 2018 by koolconvertible
	65 vert roof pump position and lines (Preview) Hi all, do i have the pump mounted upside down? having trouble with diagrams too. Which outlet goes to pump top and bottom? Ta.	koolconvertible	4	1493	Jun 9, 2018 by hawkeye5766
	Question on upper rear (Preview) Could someone please measure from the center of each bolt hole and give me the total length. The problem is that I replaced the old ones with adjustables but lost the paper with the measurement.	tramminc	7	1844	May 16, 2018 by seventy2plus2
	Help with front spindle seal/gasket (Preview) Ok so what started out as front brakes on my 65 Parisienne has turned into bearings, seals etc. The problem I have is the seal and or gasket that should be at the front backing plate and spindle were badly worn. Any help identifying/finding these parts would be appreciated. The pic is of what I should hav...	RonchoPoncho	7	1688	May 15, 2018 by RonchoPoncho
	Is it a big job to change a PB booster on a 67 Parisienne? (Preview) I've had a rebuilt and replated booster on the shelf for years now, and since I'm about to replace the master, converting to a 1"bore from a 1 1/8", I'm thinking of using it as it looks so nice compared to the original one (which currently works perfect anyway, just ugly). Is it a big job to replace the boos...	cdnpont	20	1816	Apr 5, 2018 by cdnpont
	finally got my lathe set up! turned my drums a couple of nights ago and finished the brakes (Preview) Picked this old brake lathe up a couple of years ago from a family friend who was getting rid of it. Cleaned her all up and repainted it (why not right?) and finally have it all set up. Turned the drums on the 65, and they came out great! Been a while since i've done this so i practiced on some old ones first lol...	hutch400	3	1601	Mar 3, 2018 by Pontiacanada
	upper control arms 66 bonneville (Preview) Hey everybody ....i took my upper control arms off my 66 Bonneville to replace bushings and ball joints and clean and paint . ive got them mixed up and don't know which came of what side . They look exactly the same as each other and do not appear to have any offsets or anything to not allow them to be fitted o...	jsr	0	1289	Feb 26, 2018 by jsr
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
	Steering upgrades for 67 Parisienne (Preview) Hey guys I wonder if anyone knows the scoop on steering upgrades? I have limited knowledge First off my car is power steering and it works fine! I just want to learn about upgrades I have heard you can put Camaro guts in our boxes I have heard about a 605 I dont know what our cars have? An 800???? Can someo...	SGS Welding	12	2403	Feb 24, 2018 by 65wagon
	Which American Pontiac matches with the Parisienne? (Preview) My Parisienne is leaving the shop and about to make his import trip from Venezuela to Brazil. It goes with a problem the Venezuelan mechanics couldn't fix. The car has front disc brakes, apparently adapted from a Chevy Caprice. This construction leads to a difficulty in aligning, and to an unsafe res...	fptmelo	8	2421	Aug 16, 2017 by seventy2plus2
	Wide track vs. Impala chassis ( 1 2 3 ) (Preview) Rather than totally derail the "New York Times"thread (yeah, I know, I'm usually the king of derailing....) I figured I'd ask the question in a new thread. Are you guys saying there that you think the stock wheels from a late 60's Canadian Pontiac are different than the same era Impala? (to...	4SPEED427	67	11766	Jul 20, 2017 by 4SPEED427
	They don't make them like they used to... (Preview) My Strato Chief turned 51 in May. It has 42,000 miles. It was up on the hoist the last while and when I walked by the other day, I noticed a puddle under the driver's front wheel. It appears my original shock absorber decided to leak out at such a young age and so few miles... Someone told me there is a company...	4SPEED427	14	3597	Jul 18, 2017 by 4SPEED427
	65-70 B rear spring spacers (Preview) Team, Has anyone used rear spring spacers on their 65-70 B Bodies? I have what I feel is the perfect rate in the rear, but unfortunately they have sagged a little since new. I'd like to put in another inch or so of lift, but I'm not going through the hassle of doing another set of springs. And air shocks are...	cdnpont	10	3605	May 13, 2017 by ABC123
	Anyone ever use Brakequip EZ Bend tubing? (Preview) I'm making new tranny lines for the project, so it'll have to be done just before dropping it in, when I get the trans attached to the motor. The old lines are going away with the 350 motor and TH400. I have steel 5/16 line, and man is the stuff ever hard! I can hardly bend it at all by hand, and the bending...	cdnpont	2	2647	May 10, 2017 by Beaumont67SD
«First < 1 … 5 6 7 8 9 … 20 > Last» \| Page of 20 sorted by