General Electrical Forum

alexpertkustompontiac1956 · alexpertkustompontiac1956

when i bought the car it did not come with backup lights so i bought some of ebay no the question is what type of bulb do i need for it and can i get this in NAPA or in any other auto parts store like QUEST well thank you on advance this is for a 1956 Pontiac pathfinder deluxe

cdnpont · cdnpont

I've been working on my forward harness when time permits, and this is where I'm at so far. It takes a good bit of time to do this job, and I'm glad the rad support is on my bench. Detail showing from left; horn relay, ground stud, power point junction and 40a headlamp relays. Two "Littlefuse" b...

427carl · 427carl

Would anyone have a wiring diagram, or know, where I could find, a wiring diagram for a '03 and up GM truck mirrors? I have a set of '08 power Towing Mirrors.. I have a pair of harness ends, out of wreck, that will plug into new mirrors.. I was hoping to find out "which wire" powers the "si...

cdnpont · cdnpont

When soldering, it's always nice to have somthing to hold the wire steady, I've always seemed to fight with it when doing the smaller work, and I'm trying to do a nice job with these harness connectors. So I threw together this little jig for no real cost. 12G romex, from residential 12/2. Nice a...

66 Grande guy · 66 Grande guy

Anybody ever have to deal with a really rusty fuse box? The fuse tangs on mine are so rusty the circuits don't work. Are they replaceable? The picture is pretty poor but hopefully it will show you what I have to work with.

cdnpont · cdnpont

CP electrical guru's, a couple of questions... I still have been unable to figure out a return charging wire size from the new powerpoint to the Battery. I've heard many different theories on this one. In it's stock form, it's a 10G with 14G fuse link completing the circuit back to the battery f...

cdnpont · cdnpont

I made up a colour harness diagram, from the bulkhead plug out to the running and marker lights, illustrating what my harness plan pretty much will look like. I've chosen to up the wire size on the running, signal and markers (20 to 16g), the main body power feed (12 to 10G), but reduce the old highbeam...

cdnpont · cdnpont

Just got my old grungy wiper motor back from Restoration Services in Midlothian Illinois. Had sent the motor along with some parts from a second parts motor. Beautiful job! Here's what was written on the bill; Dissasemble, clean and inspect core - the trans main shaft & cap was worn out (used o...

cdnpont · cdnpont

I have an Edelbrock carb. It has a manual choke (which I prefer), but who knows, I could be adding an electric choke eventually. In building a new engine harness, I'd like to include the power wire just to have it if it's ever needed. Will a fused 14 Gauge wire be heavy enough? Is it just one wire to the cho...

Topic		Started By	Replies	Views	Last Post
	question (Preview) when i bought the car it did not come with backup lights so i bought some of ebay no the question is what type of bulb do i need for it and can i get this in NAPA or in any other auto parts store like QUEST well thank you on advance this is for a 1956 Pontiac pathfinder deluxe	alexpertkustompontiac1956	1	1843	May 28, 2009 by 427carl
	Harness progress. (Preview) I've been working on my forward harness when time permits, and this is where I'm at so far. It takes a good bit of time to do this job, and I'm glad the rad support is on my bench. Detail showing from left; horn relay, ground stud, power point junction and 40a headlamp relays. Two "Littlefuse" b...	cdnpont	8	2267	Apr 4, 2009 by 2drpost
	Wiring diagram for Electric Mirrors (Preview) Would anyone have a wiring diagram, or know, where I could find, a wiring diagram for a '03 and up GM truck mirrors? I have a set of '08 power Towing Mirrors.. I have a pair of harness ends, out of wreck, that will plug into new mirrors.. I was hoping to find out "which wire" powers the "si...	427carl	11	2562	Apr 1, 2009 by 427carl
	A third hand for soldering. (Preview) When soldering, it's always nice to have somthing to hold the wire steady, I've always seemed to fight with it when doing the smaller work, and I'm trying to do a nice job with these harness connectors. So I threw together this little jig for no real cost. 12G romex, from residential 12/2. Nice a...	cdnpont	11	2129	Mar 12, 2009 by 59poncho
	Rusty fuse box (Preview) Anybody ever have to deal with a really rusty fuse box? The fuse tangs on mine are so rusty the circuits don't work. Are they replaceable? The picture is pretty poor but hopefully it will show you what I have to work with.	66 Grande guy	6	2302	Mar 5, 2009 by 66 Grande guy
	Question, what size battery charging wire? Fuse link? (Preview) CP electrical guru's, a couple of questions... I still have been unable to figure out a return charging wire size from the new powerpoint to the Battery. I've heard many different theories on this one. In it's stock form, it's a 10G with 14G fuse link completing the circuit back to the battery f...	cdnpont	2	3078	Mar 4, 2009 by 4SPEED427
	Forward harness Diagram. Modified slightly. (Preview) I made up a colour harness diagram, from the bulkhead plug out to the running and marker lights, illustrating what my harness plan pretty much will look like. I've chosen to up the wire size on the running, signal and markers (20 to 16g), the main body power feed (12 to 10G), but reduce the old highbeam...	cdnpont	2	1655	Mar 4, 2009 by cdnpont

	Restored! A 69' Parisienne wiper motor. (Preview) Just got my old grungy wiper motor back from Restoration Services in Midlothian Illinois. Had sent the motor along with some parts from a second parts motor. Beautiful job! Here's what was written on the bill; Dissasemble, clean and inspect core - the trans main shaft & cap was worn out (used o...	cdnpont	13	2128	Mar 2, 2009 by Canadian Poncho
	Electric choke, wire question. (Preview) I have an Edelbrock carb. It has a manual choke (which I prefer), but who knows, I could be adding an electric choke eventually. In building a new engine harness, I'd like to include the power wire just to have it if it's ever needed. Will a fused 14 Gauge wire be heavy enough? Is it just one wire to the cho...	cdnpont	3	1751	Feb 17, 2009 by cdnpont
«First < 1 … 5 6 7 \| Page of 7 sorted by