2024 Canadian Poncho Calendars are Now Available! CLICK HERE

 

 

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: " BUMMER"


Canadian Poncho Superstar!

Status: Offline
Posts: 5681
Date:
" BUMMER"


Picture 088.jpgLooks like I have to repair an "oil leak" at frt. of pan!!! Was hoping it was T/cover seal but it looks like the frt. neoprene hoop seal didn't "seat' right on pan, & started to leak. Might be easier to "pull" the engine "AGAIN" than to just lift it up enough to get the pan off???? & struggle to get it back on w/out knoking off the gaskets & end seals in a "tight" spot. any opinions on this?????? Heres the new shifter for 5 spd.



__________________

Some times I wake up GRUMPY, but today I let her sleep in    !!!!!!!! BLACKSTOCK Ont.



A Poncho Legend!

Status: Offline
Posts: 20051
Date:

That's too bad Pete. I think that the time and effort expended in bumping up the engine and fighting with that repair will be a frustration.  If you pull the engine you will most likely be able to fix it once and for all. 



__________________

Ray White, Toronto ON

1973 LeMans 454 "Astro-Jet"

Built March 9, 1973 - Oshawa ON

1993 Corvette Convertible LT 1

Built January 10, 1993 - Bowling Green Kentucky 

 




Poncho Master!

Status: Offline
Posts: 2249
Date:

Agh. Kind of like "which do you like better, a cold cup of coffee with a cigarette butt in it, or a poke in the eye with a sharp stick" eh?

Lot of work to pull the motor - unhook all cables (starter, alternator, coil, etc.), drain radiator and remove hoses (depending on clearance, maybe remove radiator too), probably remove alternator, unhook fuel line and plug it, unbolt motor mounts and bellhousing (or tranny), unbolt headers, etc. - but you are (of course) correct about struggling to get the oil pan bolts off and carefully remove the pan ... I'd try the latter, just go slow and easy, overall a lot less work. And not much torque to worry about on the pan bolts.

Shifter looks great, like your hand will naturally fall on it.

Good luck!

Dave

__________________

56Pontiac  1956 Pontiac Pathfinder 2dr sedan, 496 - dyno'd 545 hp, stick shift, 4.11 posi - Hot Rod

  1964 Acadian Beaumont SD convert, 283 - factory 195 hp, Powerglide, 3.08 10-bolt - Cruiser

  2012 US-built crew cab truck - Daily Driver and Boat Trailering

MC


Canadian Poncho Superstar!

Status: Offline
Posts: 7500
Date:

Love the shifter!  I tried out a "pistol grip" in my buddy's Super Bee recently... the shifter just feels right... good choice!



__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 5681
Date:

I got into the 52 yesterday after doing another trip, this time around the "long" block!!! & got it into 4th. gear still waiting to try 5th. Engine has all sorts of power BUT didn't sound right. Back in the shop I started pulling S/plug wires 1 at a time,no diff when #2 pulled, removed the S/plug & did comp. test [30lbs] NOT GOOD thought I'd taken a lobe off the cam but rockers were moving, Adj. the valves & BINGO too tight, re set all valves sounds "real" good now Have drained the fluids & have to decide wether to try & do pan gask. leak in the car or just "bite" the bullet & pull the SBC back out & do it where you won't be wrestling with the pan & knock the gasket & end seals out of whack!!! trying to wiggle pan back up there??????

__________________

Some times I wake up GRUMPY, but today I let her sleep in    !!!!!!!! BLACKSTOCK Ont.



A Poncho Legend!

Status: Offline
Posts: 48633
Date:

Doesn't someone make a one piece oil pan seal/gasket for your application?

That would make it easier to do wouldn't it?

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



Canadian Poncho Superstar!

Status: Offline
Posts: 5681
Date:

Carl Stevenson wrote:

Doesn't someone make a one piece oil pan seal/gasket for your application?

That would make it easier to do wouldn't it?


 Carl, going to look into that!!!  Had wondered if they make a one pc. pan gask. for small block. the frt. U seal looks like it's rolled in just abit but enough to cause MAJOR oil leak at frt. of pan



__________________

Some times I wake up GRUMPY, but today I let her sleep in    !!!!!!!! BLACKSTOCK Ont.



Poncho Master!

Status: Offline
Posts: 1915
Date:

Killer shifter! Too bad about the leak tho

__________________


A Poncho Legend!

Status: Offline
Posts: 48633
Date:

dualquadpete wrote:
Carl Stevenson wrote:

Doesn't someone make a one piece oil pan seal/gasket for your application?

That would make it easier to do wouldn't it?


 Carl, going to look into that!!!  Had wondered if they make a one pc. pan gask. for small block. the frt. U seal looks like it's rolled in just abit but enough to cause MAJOR oil leak at frt. of pan


 I'm pretty sure there is one and I think it's Felpro.

This is a 2 piece rear seal, right?



__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



A Poncho Legend!

Status: Offline
Posts: 48633
Date:

Just looked, yes, Felpro has depending on your specific year/application even though the original was a 4 piece gasket and seal kit.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



Guru

Status: Offline
Posts: 652
Date:

The Fel-Pro 1 piece for small and big blocks are NICE !! I would not build another engine without one (even though I've never had problems w/o them). They are expensive so get ready !!!

__________________

72 Nova SS - Minitubbed
70 Nova SS - #'s L-78 Bench Stick
68 Acadian SS clone - factory air
67 Chevelle rag - SS 427 clone



Uber Guru

Status: Offline
Posts: 3463
Date:

ditto on the 1 piece fel pro gskts. 

part nos...

OS 34509T '57-'74 SBC

OS 34510T '75-'85 SBC

OS 30061T BBC



__________________

 








Canadian Poncho Superstar!

Status: Offline
Posts: 5681
Date:

The block is 75 BUT I have no idea what yr. the pan is off?? Just wondering now if thats the problem, mis-matched pan & gasket set!!!!!!

__________________

Some times I wake up GRUMPY, but today I let her sleep in    !!!!!!!! BLACKSTOCK Ont.



Canadian Poncho Superstar!

Status: Offline
Posts: 5681
Date:

Dropped the pan "in the car" took out the frt U seal on pan & replaced w/new one as old one had a "DEFECT" siliconed it & waited for it to "skin" over. re-installed pan & just snugged to bolts till it sets up!!! Then tighten it up & wait 24hr. till it cures. Will know tomorrow when I "light" it up. Hope this works!!!!

__________________

Some times I wake up GRUMPY, but today I let her sleep in    !!!!!!!! BLACKSTOCK Ont.



A Poncho Legend!

Status: Offline
Posts: 20051
Date:

Fingers crossed for you Pete.



__________________

Ray White, Toronto ON

1973 LeMans 454 "Astro-Jet"

Built March 9, 1973 - Oshawa ON

1993 Corvette Convertible LT 1

Built January 10, 1993 - Bowling Green Kentucky 

 




Poncho Master!

Status: Offline
Posts: 2249
Date:

Sounds good, surely that will do the trick, and waaaaaaaay easier than pulling the motor.

Dave

__________________

56Pontiac  1956 Pontiac Pathfinder 2dr sedan, 496 - dyno'd 545 hp, stick shift, 4.11 posi - Hot Rod

  1964 Acadian Beaumont SD convert, 283 - factory 195 hp, Powerglide, 3.08 10-bolt - Cruiser

  2012 US-built crew cab truck - Daily Driver and Boat Trailering



Canadian Poncho Superstar!

Status: Offline
Posts: 5681
Date:

IT WORKED!!!!! No leak after putting the oil back in & running it for a few min. with no coolant. Put antifreeze in[only had water in it b-4] & took it for a "test" drive!!!! Thought it had "balls" b-4 but now hitting on 8 it's a "WEAPON"!!!! Even though the garage is heated, didn't want to worry about a power failure & have it freeze on me. Now I can continues on w/the project "WHEW!!!!!!

__________________

Some times I wake up GRUMPY, but today I let her sleep in    !!!!!!!! BLACKSTOCK Ont.



A Poncho Legend!

Status: Offline
Posts: 48633
Date:

That's excellent Pete. Glad to hear it.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



Uber Guru

Status: Offline
Posts: 3813
Date:

That's good news always nice when things work out.

__________________

1957 Pathfinder deluxe 4 door wagon
1961 Pontiac Parisienne bubble top Traded for a Harley sorry guys.

2007 Grand Prix Gxp

2009 Pontiac Montana SV6

Winnipeg MB 



A Poncho Legend!

Status: Offline
Posts: 20744
Date:

All within one week ... you retirees don't fool around!biggrin Great news!



__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.

Page 1 of 1  sorted by
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.