|
Lower door pin R+R
(Preview)
Well I popped the drivers door off today to put new springs n bushings. The top one was simple enough. I however cant get the pint out of the lower hinge. The bottom of the pin is all flattened out from some body else's doing. Just wondering what you guys do to change the lower pin n bushings? I have been se...
|
bowtieboy
|
2
|
1099
|
|
|
|
64 center grill part
(Preview)
I don't know if anyone else has run into this. I have (2) parts with the same # 5733022. As can be seen in the pictures one has a ledge above the stub and onther dosen't. Also piece with ledge is 3/16 narrower than the other. Parts book does not list is #. Both pieces are from 64 Beaumont. Anybody got ideas. Wo...
|
Brian
|
1
|
1250
|
|
|
|
Help with tail light question on Beaumont
(Preview)
OK I need some help here!! I am wondering if this is a Beaumont rear? I took the picture years ago... hmmmm 30? or so
|
the70judge
|
12
|
1639
|
|
|
|
Door hinges
(Preview)
My doors are taking a little more effort to close as they must be sagging. Are the hinges ajustable, or is replacing them with aftermarket hinges the better option? thx
|
03cts sport
|
19
|
1603
|
|
|
|
69 Beaumont headlight trim part #
(Preview)
do they use the same part # left and right ??
|
rabbit64cs
|
9
|
1922
|
|
|
|
1965 sheet metal
(Preview)
i just took the rear bumper off the 4 dr sedan , noticed that the piece of metal between bumper and body is pretty rough. does any place make this or do i have to make a filler for it.
|
RAILSKINNER
|
17
|
2482
|
|
|
|
Removing rear window trim?
(Preview)
Well I have a slight leak in my back window of the 67. When i had my windshield done the guy had suggested that I try and pump some sealer in it before having a glass shop do it. So my question is what tools/ tricks are involved to get the trim off? Thanks, Jesse
|
bowtieboy
|
2
|
1212
|
|
|
|
|
69 Beaumont mirror?
(Preview)
|
rabbit64cs
|
0
|
1078
|
|
|
|
EPOXY PRIMER ????
(Preview)
What happened to all the good ( PPG - RM ) epoxy primer? Tried to get some more RM ep-689 epoxy today and was told it is no longer available so I tried to get some PPG DP line and same thing no longer available.No more good epoxy? I have worked with the PPG omni epoxy but it does not come close to the old stuff whe...
|
65post
|
1
|
7096
|
|
|
|
Fender Trim
(Preview)
I have a 66 Beaumont Custom that has chrome fender trim leading down the top edge of the fender. Is this an option only for custom models?Most of the Beaumonts I see at the shows here are SD models and I have yet to see this on any other 2dr beaumont. I have been looking for a replacement piece for the dr...
|
BLACK BEAU
|
9
|
1737
|
|
|
|
After 19 years I can still paint.
(Preview)
On saturday I got the car to the bodyshop and the owner said Knock yourself out. It took from noon to six to complete the paint job. After 19 years of not painting I found that my body is not as fit as it was. My legs and sholders are killing me.Here are some pics.
|
chevy4ever
|
7
|
1623
|
|
|
|
Barbeque
(Preview)
I was at a car show yesterday with my 67 beaumont custom and the barbeque was lit up to provide burgers and dogs for the masses, although i was some distance from the barbeque there was a fairly strong wind and it was blowing towards my car and a few other ones. I scrubbed it clean when I got home but my D99 tw...
|
67custom
|
10
|
1713
|
|
|
|
help with chrome clips
(Preview)
my small clips that hold the upper trunk piece on are mostly broken, any one had any luck with finding them ?? Thanks
|
Lefty
|
2
|
1539
|
|
|
|
1969 Fenders
(Preview)
Well I started fitting my front end together and the drivers side fender was previosly worked on and the front bracket the attaches to the inner fender was rewelded in the TOTALLY wrong position, rather than screwing around with a bad job to start with I am considering buying a new drivers side fende...
|
mylo
|
6
|
2194
|
|
|
|
|
66 SD body side trim options
(Preview)
Hi, I am a new member doing a frame off rebuild on my 66 SD. Although it is not a stock restoration, I would like it to have all the trim that it was standard on an SD. I have all the Body side trim but it is rough. Was wondering if 67 Chevelle side trim was close in size and shape to the stock 66 SD trim.
|
1320 SD
|
22
|
2636
|
|
|
|
DTStainless - Beuamont trim remanufacturers
(
1 2
)
(Preview)
Hi there. My name is Taylor and I am the co owner of DTStainless. I hope that I am not breaking any site rules by posting this. We are a new company running out of ontario, canada who is remanufactureing Beumont trim. We remanufacture Chevelle trim specifically to the Beaumont out of stainless steel ins...
|
DTStainless
|
26
|
3851
|
|
|
|
Beaumont wiper motor?
(Preview)
Years ago I bought a bunch of parts from a 68 - 69 Beaumont. I've since sold all the tail lights and grilles etc. But I have a few parts left. I'm wondering if anyone can recognise whether this is a Beamont wiper/washer assembly or not. And if this is a blower and cage for the same thing.
|
StriperSS
|
6
|
1832
|
|
|
|
" SD-396" STRIPES ARE ON
(Preview)
well thanks to john the stripes went on with know major issues it took about 4hrs. the stripes sure give the car a different look....
|
wagon64sd
|
20
|
3423
|
|
|
|
65 Beaumont Clock
(Preview)
Hi all, looking for a working clock for my 65 Beaumont. Saw one on ebay a couple weeks ago but I was too late to bid on it. Any help would be greatful.. Mark.
|
Mikies Beaumont
|
5
|
1209
|
|
|
|
65-66 beaumont glove box door
(Preview)
Hi like to no is the 65 and 66 beaumont glove box door the same or will a 65 fit a 66 .thanks .
|
65acadiantoplist
|
2
|
1205
|
|
|