Enjoy 5% OFF at VEVOR Canada! and Support Canadian Poncho at the Same Time!
Members Login
Username 
 
Password 
    Remember Me  
Canadian Poncho Homepage -> Canadian Poncho -> General Beaumont Discussion -> Gah....my body mounts
Post Info TOPIC: Gah....my body mounts
Paulish


Guru

Status: Offline
Posts: 778
Date:
Gah....my body mounts
Permalink  

I changed all my suspention this year and today was my first test drive...So I back out of my shop and hit a little bump and hear thump from my rear end.
Pull back in check the springs are in right.....yup even have upper and lower isolaters in right. So I back out again...thump. HMMM...I have to drive my car to the alingment shop tommarow, what could this be? Put my car on the hoist ....everything looks good, no loose nuts. Hmm what's this peace of rubber sticking out here? O it used to be a body mount. Cleverly disguised with thick undercoating!!  shocked.gif 
I want to drive my car and have no plans on frame off this year. Any suggestions on changing them. I bought a new set of the poly dougnuts but i think ill need hardware too. These are carridge nuts arn't they? I have a duck bill port-o-power and i'll try to lift the body with that. Anyway any help will be appreciated.
confusedconfusedconfusedsun.gif



__________________


Paul
67 Beaumont 2dr/ht

 454/t400/9inch

In Lethbridge, Alberta

My build thread! Starting over, My 67 Beaumont build thread.
4SPEED427


A Poncho Legend!

Status: Offline
Posts: 50210
Date:
Permalink  

I am in the middle of that job for someone on an A body at the moment, although my Acadian has priority for the next while.

Are you looking to change them all?

Which mount is falling apart?

I have the body separated enough from the frame right now. Once I got the bolts out (or borken off enough) it was pretty easy to lift. I went to Princess Auto and bought 4 little one ton jacks and used about 2 foot lengths of 2x4 on each one. It comes up fairly easy.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Paulish


Guru

Status: Offline
Posts: 778
Date:
Permalink  

it looks like the rear 4 or 6 need to be done fore sure. I'm planning body off resto/mod in two years or so so I can change the rest then.

__________________


Paul
67 Beaumont 2dr/ht

 454/t400/9inch

In Lethbridge, Alberta

My build thread! Starting over, My 67 Beaumont build thread.
4SPEED427


A Poncho Legend!

Status: Offline
Posts: 50210
Date:
Permalink  

Chances are you will break the bolt on the mount right behind each rear wheel. It the bolt doesn't break, the nut will spin inside the mount and the only way to that nut is to cut open the trunk floor or cut a small rectangular piece out of the wheel tub behind the wheel.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
Paulish


Guru

Status: Offline
Posts: 778
Date:
Permalink  

Well i finally got around to doing them today. I only had one that actually turned out so now i have holes all over my floor and trunk but no more(bump thump bump). It wasnt that hard but took me the hole day. Also helped I had a hoist to use. But now I know I really need to do a frame off cause I found a lot of nastyness, especially around those rotten mounts.
Anyway new seats,carpet and door panels tomarow so im ready for street wheelers weekend next weekend and my wedding the following one...

I can smell the burnt rubber allreadysmile

__________________


Paul
67 Beaumont 2dr/ht

 454/t400/9inch

In Lethbridge, Alberta

My build thread! Starting over, My 67 Beaumont build thread.
4SPEED427


A Poncho Legend!

Status: Offline
Posts: 50210
Date:
Permalink  

Street Wheelers is next weekend? My brother in law who lives there always talks about that.

So what do you mean by holes in the trunk and floor? Did you have to cut holes to hold the nut from spinning?

The mount right behind the wheel is usually the one that rusts the worst. You can just make a new piece and weld it on like the factory piece was. It will look good as new.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
Paulish


Guru

Status: Offline
Posts: 778
Date:
Permalink  

Hi Carl...
So yes I had to cut holes all over.It was painful my car doesnt need floor pans ....but
No#1 bolts busted as soon as the impact hit them,#2 both spun 3&4 broke,5 one spun one broke and i dont have the one after the rear wheel well. (My car is mini tubbed) and the person who did it (before i owened it)must have cut of those mounts. The last ones by the rear bumper were ok .

-- Edited by Paulish at 11:29, 2008-07-06

__________________


Paul
67 Beaumont 2dr/ht

 454/t400/9inch

In Lethbridge, Alberta

My build thread! Starting over, My 67 Beaumont build thread.
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Numbers_guy


Addicted!

Status: Offline
Posts: 301
Date:
Permalink  

Hang in there Paul.

Look at it from this point of view.   Your making up for some past sins and wear factors.   If done right, and it sounds like that's the way you're doing it, then your Beaumont is good for another forty odd years.

With you buddy, sounds like the cars going to be back to new soon.   Keep us advised.

__________________
Dave Weir Member #1 Canadian Classic Chevelles & Beaumonts http://cdnclassics.chevelles.net/
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
Canadian Poncho Homepage -> Canadian Poncho -> General Beaumont Discussion -> Gah....my body mounts
Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.