69 Parisienne bonnet hinges

Confederate1 · Member

69 Parisienne bonnet hinges

73SC · A Poncho Legend!

Are these the same ones you need?

CLICK HERE

Confederate1 · Member

Thanks for the reply but they look to mount differently but because I dont have 69 hinges to compair with I cant be sure. My car at the moment has 68 hinges on it but the hood dosnt sit properly at the windscreen

67BBSD · Canadian Poncho Superstar!

sorry never thought about hood hinges-automatically was thinking door hinges-will look around

Ghost Post · Poncho Master!

Cool car Herby!.
Is it a 327 car?.
Look closely at and measure any GM car hinges you can find there as many of this era hinges swap Ok in pairs..

Anybody here have a set to help this fella out?.

Here's as few pertinent Hollander listings noted below..
Keep in mind cars noted as Pontiac or Chevrolet Pass are B-Bodys also that these listings are for US cars, not Canadian Ponchos..

H#161
Pontiac 69-70
Tempest 68-72
* Wreckers say #134 fits

H#134
Chev Pass 68
Chevelle 68
Nova 68-74
Omega
Ventura 71-74
Apollo 73-74
* Wreckers say #161 fits

#129
Chev Pass 69
Chevelle 69

# 130
Chev Pass 70
Chevelle 70-72
GMC Sprint 71-72
Monte Carlo 70-72

smile

Confederate1 · Member

Thanks Pete, it was a 327 car but has been replaced with a Corvette 350 pulled out to 383 and still runs the 2 speed glide.

Canadian Poncho · A Poncho Legend!

I didn't know 327's were available in 69 Parisiennes. Is this just for export? As for hood hinges, I'm pretty sure 69 Impala are the same. Carl, can you check your parts books?

Ghost Post · Poncho Master!

Herby,

So the '68 hinges fit Ok but you can't adjust them down any further so the bonnet fits lower at the rear edge?. Does your car have any protruding height adjustment pegs at the rear edge?.

Is your car a RHD car and shipped out of Canada as a CKD?.
If RHD, is your dash panel steel or fiberglass?
Some underhood & interior pics would be cool including shots of the cowl as it's interesting seeing the different steering, brake, wiper linkage and sometimes unique cowl vent cover as well as dash & other factory mods necessary for RHD cars..

Are you aware for minimal cost GM Canada can supply documents showing options/colors etc originally shipped w/ your Vin?.

smile

-- Edited by Ghost Post at 10:29, 2008-09-18

SD 396 · Poncho Master!

I double checked the numbers in the GM parts book and came up with the same as Ghost Post except for the additional ones that may fit.
They are listed in GRP 8.015 part number 9794024 for right and 9794025 for left.
1969 and 1970 full size CDN and US Pontiac full size
1969 to 1972 Lemans/Tempest
All of the Chevrolet hinges do not directly cross over and assume that they may need to be modified to bolt on. Which means drilling new holes.
Either of these cars can supply the hood hinges you need. They should not be difficult to locate some in North America. You may want to check on ebay or an aftermarket supplier for GTO parts if you can't find someone on here with a set.
Hope this helps.
Welcome aboard,
Brad

Confederate1 · Member

Thanks for the all the help gentleman. Pete, I'm off for aweeks holiday but when I get back will post some pictures for you to look at. The car is factory RH drive with a full steel dash.

Howmac · Guru

Are you still looking for some hood hinges?

If so , I should have a pair for you. ( Canadian built 69 Pontiac)

Howard