Save 5% at Vevor and Support Canadian Poncho!
Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Ignition system help


Veteran Member

Status: Offline
Posts: 85
Date:
Ignition system help


O.k. I headed out to see if I could awaken the mighty 283 from it's 20 year slumber. after new plugs, oil, filter, air breather, belts, battery, and rolling it over to make sure it wasn't siezed; I discovered I had no spark.

I checked my coil resistance and from + to - I have 6 Ohms and from + to output I have 16K Ohm I also checked my voltage @ the + side of the coil and found it's @ 6V, is that normal or should it be @ the full battery voltage?

As simple as these old ignition systems are supposed to be I have no experience with them and no shop manual.

could someone please help point me in the right direction?

Thanks in advance.



__________________

www.bobgetsresults.com



Guru

Status: Offline
Posts: 545
Date:

Did you check the condition of the breaker points. They may be corroded from sitting that long.



__________________
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


Veteran Member

Status: Offline
Posts: 85
Date:

again not familiar with this system and no book, so you'll have to assume I know nothing. where can I find the breaker points? are you talking about the actual points in the distributor? because if so I don't even have any juice comming out of the coil from what I can tell.



__________________

www.bobgetsresults.com



Canadian Poncho Superstar!

Status: Offline
Posts: 7796
Date:

yes, the breaker points are the points within the distributor.   You must make sure they are in good working order, with the gap set at appx .020".   They are an integral part of the ignition system, and without them in good working order you WILL NOT get any spark.    I'm not sure what the +6V reading at the + side of coil is telling you, but I suspect that may be ok as there is a ballast resistor ahead of it, which drops the voltage from +12V.

While you're at it, change the points & condensor (modern sets are a combination of points and condensor), rotor and distributor cap.  New wires would also be a step in the right direction.



__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop

 

 



Veteran Member

Status: Offline
Posts: 85
Date:

O.K. I snaped a few pics, I'm assuming I have 2 condensors in this setup, would this be a problem?  also does anyone have the resistance specs for testing one of these coils?

 

distributorcoil



__________________

www.bobgetsresults.com



Veteran Member

Status: Offline
Posts: 85
Date:

Well After checking my coil, and finding this bit of information on the interweb I have come to the conclusion that my coil is no longer viable.

http://waywardgarage.com/129/testing-an-automotive-12-volt-ignition-coil/

 



__________________

www.bobgetsresults.com



Canadian Poncho Superstar!

Status: Offline
Posts: 7796
Date:

the breaker points you have are one of the combination points & condensor in one.  That's ok, but have you checked to ensure the points are good or not?   They MUST be able to open and close for the coil to produce spark.   (when the points are closed, the coil is grounded and will not spark.   When the points open, it removes the ground and allows the coil to spark.    If they're stuck open - which is often the case, the coil won't spark either).

The other capacitor on the + side of the coil is normal.  It's not the condensor we're talking about, I believe it's part of the system to reduce ignition noise in the radio.



__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop

 

 

Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


Veteran Member

Status: Offline
Posts: 85
Date:

I'll go climb under the bonette tomorrow and inspect the points a little closer and see whats goin on and let you all know what I find.



__________________

www.bobgetsresults.com



Poncho Master!

Status: Offline
Posts: 1467
Date:

condensors have a very short life, 6 years  at most. back in the day, an annual tune up included changing plugs, points and condensors every year and coil about every five years to maintain peek performance. Now that we only drive our classic pontiacs a few thousand miles each year.(if were lucky) we forget some components die with age,not mileage.



__________________

pontiax- (canadian pontiac X frame)1964 Parisienne 2dr. Hardtop ,lagoon aqua metallic (Q) ,421 cid Dart Industries block and heads. 550 hp. 575 ft lb  of torque.

 



Veteran Member

Status: Offline
Posts: 85
Date:

Well everyone I would like to thank you for all the good advice, once I setup the points and cleaned all the contacts etc. the car fired right up and idles like a champ.

Took it out for a little tour around town, needs a little work but it moves under it's own power.

thanks again.



__________________

www.bobgetsresults.com



Canadian Poncho Superstar!

Status: Online
Posts: 7183
Date:

clean the points with a file,, you'd be amazed at what havoc an invisable coating of oxidation will do !

__________________

later...rog

AADD supporting member !!
I'm a collector...not a builder!!Located in sunny central Saskatchewan at the lakehead!
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.