Save 5% at Vevor and Support Canadian Poncho!
Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: my 63 283 Re&Re


Addicted!

Status: Offline
Posts: 335
Date:
my 63 283 Re&Re


Question....I wasn't going to pull the pan on the 2 spd but once I got it clean I saw drips at the shift shaft...I was told this had been done....so off with the pan..blah blah shift shaft seal and o-ring...wix filter and gasket..now, I took out the speedo bullet to do the o-ring there and noticed it was a little"growly" whem I spin the gear. Definitely needed an o-ring,but..how do I get the gear out of the bullet?? This is not like newer ones that have a seal.I don't want to force it and it does not seem to leak internally but there must be an o-ring inside the bullet. It seems like the gear is crimped at the speedo end? Anyone know about this/these? Maybe it's a transition piece from the cast housings to the aluminum version.The gear is plastic and in good condition. There is a flat boss on the pan that would be for a drain plug so I will make one and weld it in while I have the pan off.

__________________


Addicted!

Status: Offline
Posts: 335
Date:

IMG_0300.JPGIMG_0304.jpgIMG_0301.jpgIMG_0302.jpgIMG_0303.jpg      Here are some images of my indecision/decision process regarding drilling a hole in my transmission oil pan. I know one can buy stuff but I have junk laying around and like a challenge. ....first a malleable iron fitting,cut off and welded in (they do weld) next I found a 316 stainless reducer (yup I worked at a wasteful pulp mill for a while) so I pared that down with my zip cut disc and polished it up. I found an 1/8 pipe plug in brass. Not quite your plug/washer setup but workable and a nice size as to not look too out of place.....



Attachments
__________________
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


A Poncho Legend!

Status: Offline
Posts: 20744
Date:

I like bodging together and re-purposing things out of found items. Good stuff!



__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.



Addicted!

Status: Offline
Posts: 335
Date:

Ya,my old dad, (gone for the big dirt nap),was the greatest recycler I have ever known.He/we also lived on a small island between BC's mainland and Vanc Island. You can't just run to the store and get stuff....He had the largest collection of used nails I've ever seen! lol. Any thoughts on getting the gear out of my speedo bullet Darryl?

__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 5736
Date:

Post a pic of your speedo bullet, it should be the same as on a manual transmission. If its the one I think it is, the oring is on the outside and the plastic gear should slide out easily and spin easily.

__________________

63 Parisienne sport coupe (The Big GTO), black, maroon interior, 409 4 speed; former owner of a 59 El Camino, 63 Corvette SWC, 62 Chev Bel Air SC.
1963- Pontiac top selling car in Canada

Mahone Bay, NS Still not old enough to need an automatic



A Poncho Legend!

Status: Offline
Posts: 20744
Date:

DonSSDD wrote:

If its the one I think it is, the oring is on the outside and the plastic gear should slide out easily and spin easily.


 Yes, this rings a bell ... I was parting a Powerglide car out, so really didn't pay too much attention to how it came out, as long as I got it out.



__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.



A Poncho Legend!

Status: Offline
Posts: 20744
Date:

otus wrote:

Ya, my old dad, (gone for the big dirt nap), was the greatest recycler I have ever known. He/we also lived on a small island between BC's mainland and Vanc Island. You can't just run to the store and get stuff.


I might have him beat. I tell everyone that I'm close to to check with me first before going to a hardware store. Sometimes on PEI a certain piece is not readily available.

I inherited my Dad's collection when he passed in 2003. He was a hardware freak, working in the stock/stores room at a factory. Then, I bought out a defunct '30s-'70s hardware store in 2005 and moved the tonnage to PEI from Toronto.

I LOVE vintage hardware ... made outside of China, Taiwan, India, etc.



__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.

Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


Guru

Status: Offline
Posts: 636
Date:

Pontiacanada wrote:
DonSSDD wrote:

Many wire that flapper open or replace with a spacer-

Don


 I just removed the flapper and Cold Weld epoxied the flapper pin holes. Instant spacer.


 Thanks Don, great idea as I was think how to go about without having to go to a exhaust shop or god forbid try to make something myself disbelief.  I have that flapper but it's not needed as I have a Carter with elect. choke. but was thinking that even when the flapper is open (mine moves freely so I "assume" it opens when hot, didn't check) it would still have some restriction on the exhausts.

Thanks again for this detailed thread....I like it :)



__________________


Addicted!

Status: Offline
Posts: 335
Date:

Jeesh! I'm with you Darryl on the hardware front! Old well made stuff....like our cars biggrinbiggrin I'll get a pic going of my "bullet". I thought for sure the plastic gear would just slide outa there but......not. I've been hosing it down with WD 40 from the cable end and it has started spinning nice and free. No oil drips out underneath it it just fills up and over flows ...To clarify..I have it standing on the bench gear end down and spray WD 40 in it from the top/cable end and spin it as I do this. nice and free and no leaks but gear does not dislodge from inside of the bullet 



__________________


Addicted!

Status: Offline
Posts: 335
Date:

IMG_0305 (1).jpgIMG_0306 (1).jpgIMG_0307 (1).jpgIMG_0308.jpg  Here are pics of my speedo bullet...Looks like a regular unit?? The shift shaft seal I got from Rock Auto...wrong part...too small for my unit. I do see what I think are correct ones on E-bay. I went to my local parts store for help and they have a seal coming but his "tranny guy" said "tell him to put two in there" . The seal seat will not accept a double up on the seal...it's just deep enough for one. These are tiny little seals.  The SO-19 is too tiny! 



Attachments
__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 5736
Date:

It should pull out easily, it is floating in transmission fluid when in the car, it shouldnt have needed wd40 to loosen it? Find a small bolt the size of the end of the plastic and gently tap it out. Check the inside of the bullet for rust or other issues.

__________________

63 Parisienne sport coupe (The Big GTO), black, maroon interior, 409 4 speed; former owner of a 59 El Camino, 63 Corvette SWC, 62 Chev Bel Air SC.
1963- Pontiac top selling car in Canada

Mahone Bay, NS Still not old enough to need an automatic



Addicted!

Status: Offline
Posts: 335
Date:

IMG_0310.jpgIMG_0309.jpgIMG_0315.jpgIMG_0314.jpgHey Don. The gear wasn't stuck. Just a bit "growly" when I turned it by hand hence the WD..I'm just a little uncertain about tapping the gear outa there..It seems as though it is factory peened (for lack of a better term) at the speedo end which retains a little plastic disc in there. Maybe I worry too much. Photos of the hole in my pan and the tools used to create it...a change up in my brass plug selection and the date code on the bottom of the pan. I may or may not post my welding of said plug   lol



Attachments
__________________
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


Canadian Poncho Superstar!

Status: Offline
Posts: 5736
Date:

Ive not seen one peened, it may have gotten damaged or hot and melted a bit. No need for a peen, the gear cant go inward when installed, that may be why it is growly. Id replace it, they are cheap and easy to fix plus it may be good to clean out that bullet.
Nov 14 must match the rest of the date codes on your car?

__________________

63 Parisienne sport coupe (The Big GTO), black, maroon interior, 409 4 speed; former owner of a 59 El Camino, 63 Corvette SWC, 62 Chev Bel Air SC.
1963- Pontiac top selling car in Canada

Mahone Bay, NS Still not old enough to need an automatic



A Poncho Legend!

Status: Offline
Posts: 20744
Date:

otus wrote:

IMG_0315.jpg

Hey Don. The gear wasn't stuck. Just a bit "growly" when I turned it by hand hence the WD..I'm just a little uncertain about tapping the gear outa there..It seems as though it is factory peened (for lack of a better term) at the speedo end which retains a little plastic disc in there.

I may or may not post my welding of said plug   lol


I ran across the spare I have the other day, and the gear slips in and out freely.

The plug looks good from the outside!



__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.



Addicted!

Status: Offline
Posts: 335
Date:

IMG_0328.jpgIMG_0329.jpg                 So here are pics of the speedo gear out of the bullet. I used a small punch the right size and tapped the gear out.In the process a chip came off but not too much.You can see in the first pic(look at the shadow) the chamfered end and groove behind it at the cable end. The white/clear plastic washer with the little nubs on it was/is "snapped" over the chamfer and thus retains the gear in the bullet in this particular application. Underneath the washer is the metal cup and o-ring. Microscopic grit was causing the growly thing.   I use glasses, a 4x visor, a lighted bench mounted magnifier and also a usb microscope to look at stuff. I will polish up the plastic gear with some jewellers rouge ,install a new o-ring, lube and reinstall.....Hopefully the chamfer doesn't shed any more chips in the process.............



Attachments
__________________


Addicted!

Status: Offline
Posts: 335
Date:

IMG_0340.jpgTranny done....March 1rst.. No pic of my plug mig weld job sorry I did weld it on the inside and cleaned the weld up with a burr in my foredom tool. I'm sore it'll be leak free. Pesky bullet back together and installed. Painted various bits black and installed the pan. The park pawl shaft fell out while I was trying to reinstall the shift shaft. I have zero experience here so this proved to be troublesome for me and my bad eyes but I got it eventually. Now,finally, I move onto/into my engine bay...lots of grime but I will just clean it with no painting....Nice to get at the firewall with the drive train out of the way.Next year/winter I'll do suspension bushings and body pucks. I'll post pics as I move forward incl the motor and trans bolted together with spark plug wire routing before I reinstall



Attachments
__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 10632
Date:

Nice job!

How did you get that case looking so good?



__________________
 67 Grande Parisienne 4 door HT. 69 Parisienne Convertible.
 
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


Addicted!

Status: Offline
Posts: 335
Date:

Well, it took forever with a dull bench knife to literally cut all of the "glued on" grime off, then I washed it down by hand several times with wax'n'grease remover and also a can of brakekleen in there somewhere. I then used a combo of simple green and super clean with scotchbrite to scrub it some more! I also carefully used dilute muriatic acid on the cast bits. At no point did I use steel wool due to the possibility of getting fibers inside the case.Also no sharp implements or sand paper. I made sure to rinse the cast areas(pump cover etc) really well as muriatic acid will keep on working if you don't. I was careful not to get acid on the aluminum. Next I used a combo of automotive polishes...I tried several products here...a course cut, a glaze, and also used autosol. Autosol is a superb product imo. All this by hand only. I use blue shop towel, cut up blue jean denim(the real stuff) and pure cotton like bed sheets or old t-shirt material if you can find any good cotton rags these days! Finally, after installing fittings in my elbows...tons of elbow grease! lol Thanks for this question as most of this stuff I do by rote. There's no clear or anything on it...it will dull up pretty quick but at least it's clean! cheers

__________________


A Poncho Legend!

Status: Offline
Posts: 20744
Date:

You can eat off that trans! A lot of work, but it looks great!



__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.



Canadian Poncho Superstar!

Status: Offline
Posts: 5736
Date:

 

Pontiacanada wrote:

You can eat off that trans! A lot of work, but it looks great!


 what he said. Try slowly running that speedo gear (I assume no fluid in there yet) to make sure it has no binding? Muncies clean up nice like that too as do super t10s.biggrin



__________________

63 Parisienne sport coupe (The Big GTO), black, maroon interior, 409 4 speed; former owner of a 59 El Camino, 63 Corvette SWC, 62 Chev Bel Air SC.
1963- Pontiac top selling car in Canada

Mahone Bay, NS Still not old enough to need an automatic



Addicted!

Status: Offline
Posts: 350
Date:

Yikes, a ton of work but awesome result!!!  Mine is a ball of grease and crap, not looking forward to cleaning it:(  I was considering using a putty knife to lift on the top heavy layer, then degreaser and a pressure washer with 3,000 psi to hopefully lift off the rest.  Has anyone tired the pressure washer route?  I'd like it to look like this when done but not yet retired and so much else to do.



__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 5736
Date:

Glenn, Id use easy off oven cleaner, the name brand in the blue can. Ive used it on paint and
Grease, but not on aluminum. Wipe it down with a varsol solvent and a rag. Should work great. Pressure washer would work too, but you may push the water into the transmission through old seals?

__________________

63 Parisienne sport coupe (The Big GTO), black, maroon interior, 409 4 speed; former owner of a 59 El Camino, 63 Corvette SWC, 62 Chev Bel Air SC.
1963- Pontiac top selling car in Canada

Mahone Bay, NS Still not old enough to need an automatic

Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


Addicted!

Status: Offline
Posts: 350
Date:

Thanks Don.  My glide is cast.  Once it's clean and fit to work it will be serviced and new seals anyway.



__________________


Addicted!

Status: Offline
Posts: 335
Date:

Yes..not retired over here either... I didn't use a pressure washer because of my fear of water ingestion. Oven cleaner is a good idea.



__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 5736
Date:

Glenn, forgot your 62 had a 283, they got cast iron. Oven cleaner will work really well, may have to do it a couple of times and it will remove any paint as a bonus.

__________________

63 Parisienne sport coupe (The Big GTO), black, maroon interior, 409 4 speed; former owner of a 59 El Camino, 63 Corvette SWC, 62 Chev Bel Air SC.
1963- Pontiac top selling car in Canada

Mahone Bay, NS Still not old enough to need an automatic

«First  <  1 2 3 4 5  >  Last»  | Page of 5  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.