2024 Canadian Poncho Calendars are Now Available! CLICK HERE

 

 

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: 65 B Body column bearing, excess play. And a horn contact question.


Canadian Poncho Superstar!

Status: Offline
Posts: 10063
Date:
65 B Body column bearing, excess play. And a horn contact question.


I've replaced the upper bearing in the 65 column, and there is at least 1/8 of up and down play in the wheel now. Looking at the shaft as it passes up through the bearing, it's tight on the inner race, the outer race is seated in the switch housing solid as well.

The bearing is super sloppy between the races. Is this normal for a replacement bearing? It's totally unacceptable. Am I missing something here? 

 

Oh, and I cant get my horn to sound. I can ground the contact and it will, but not if I assemble it.

Is this all the parts for a 65? Am I short a part or so? According to a Chevrolet shop manual, looks like that all the parts. Unless there is some kind of contact bushing at the wheel nut?

ring.jpg

wheel.JPG

 

 



Attachments
__________________
65 Laurentian post, 67 Grande Parisienne 4 door HT. 
 


Canadian Poncho Superstar!

Status: Offline
Posts: 4508
Date:

These illustrations are straight from the 65 Canadian Pontiac chassis shop manual. Hope they help.

img012 (2).jpg

img013 (2).jpg

img014.jpg



Attachments
__________________

62 Catalina 2 dr post project

69 Parisienne 2 dr ht 427

55 Bel Air 2 dr post 265PP/PG

68 Bel Air 2 dr post BB project

 



Canadian Poncho Superstar!

Status: Offline
Posts: 10063
Date:

Thanks John.

I can't for the life of me see how that larger silver "Bellville" washer makes contact with the metal of the steering wheel hub.

It's all stacked correctly, just as seen in the large blown-up illustration.



__________________
65 Laurentian post, 67 Grande Parisienne 4 door HT. 
 


A Poncho Legend!

Status: Offline
Posts: 48634
Date:

Does the horn ring feel correct when you move it to blow the horn? You know how it should feel spring loaded and snap back into non-blowing position?

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



Canadian Poncho Superstar!

Status: Offline
Posts: 10063
Date:

It does Carl. Not super direct, but it does go in and out.



__________________
65 Laurentian post, 67 Grande Parisienne 4 door HT. 
 


Canadian Poncho Superstar!

Status: Offline
Posts: 10063
Date:

I have a spare wheel, and I just put the assembly together. Tightened the 3 screws up more than before. If I push in straight from the center I get that "click" sound. I only just realized that you need that snap, or that the washer needs to pop into to opposite shape. Kind of like those old metal toy clickers from years ago!

From the bottom horn ring or sides, it's close, but not quite the snap.

I have a couple of ideas. I might trim the ends of the 3 screw spacers just a hair, and sand down the center of the hub on the good wheel. It might have a bunch of clearcoat hindering the contact.



__________________
65 Laurentian post, 67 Grande Parisienne 4 door HT. 
 


Guru

Status: Offline
Posts: 623
Date:

i have run into this situation several times.Because the technician is in a hurry they yank on the steering
wheel instead of using a puller,after several removals over the years the bottom mounts at the rag joint
are bent.this causes the excessive up&down movement. the correct height should be 1 3/4 in. as illustrated
in g paris's post.Looks like the best repair would be to pull the column and repair.

__________________
bob lewis


Uber Guru

Status: Offline
Posts: 3986
Date:

Do you have ground from the steering shaft ? On my Camino I had to clean the shaft before mine honked. You shouldnt have to trim the spacers.

Connect the spring loaded plunger to a good ground. Horn should work by doing this. 



-- Edited by 65Camino on Wednesday 14th of October 2020 09:51:39 PM

__________________

Remember Fun,

 Remember Laughter ?



Canadian Poncho Superstar!

Status: Offline
Posts: 10063
Date:

Thanks for the comments,

The column was rebuilt, new bearings, rag joint. It's almost like there should be a tension spring or bushing under the steering wheel, acting on the upper inner bearing race. Like the bottom. But I know there isn't.

I have tensioned up the bottom spring. Maybe needs lots more?  I don't think the ears on the bottom of the shaft are bent, but it's certainly worth a look. On the B body you can get any number you'd like by moving the jacket in or out of the firewall mount. There is a slot about 1.5" long in the upper jacket tube that receives a small tab in the dash mount that gives lots of fore and aft. Might just pull the whole thing anyway and start anew .

 

No ground strap from the shaft to the steering box yet, but I jumpered a ground from a joint bolt to a body ground. Crossed the contact to the steering wheel bolt and got horn.



__________________
65 Laurentian post, 67 Grande Parisienne 4 door HT. 
 


Guru

Status: Offline
Posts: 887
Date:

Check the metal tab on the steering coupler at the box. Mine was acting strange as the horn would chirp when turning the wheel to one side only. The metal tab was broken and randomly making contact.



__________________

65 Custom Sport Convertible

Southern Alberta



Canadian Poncho Superstar!

Status: Offline
Posts: 10063
Date:

Thanks for all the comments guys,

Wheel is nice and tight now.

Bob, you were right on track with the comment about the shaft needing to protrude 1 3/4 proud of the column wheel end.

Turns out, I was about 1/8 too far out, so the column tube was much too far down through the firewall. Pushing it back into the car until it was at the correct point got it on the right track.

But some things I've learned, is what always sets the gap between the wheel and the column is the signal cancel cam inside shoulder. It acts as a bushing against the upper bearing inner race. These column bearings are sloppy until the inner race is tensioned into the outer. One important thing to remember, is that before the final tightening of the dash clamp gets done, the shaft flange should be bolted and tightened (not too much) to the rag joint. The little spring and clamp at the bottom of the shaft acts the same as the cancel cam, and sets the bottom bearing tension.

 

Upper bearing and cancel cam, note the beveled shoulder of the cam. It nests into the bearing inner race shoulder and tensions it against the outer race.

cc.jpg

 

Horns: got the contactor set to work at the ring, but low and behold my horns are dead now!

Anybody got working horns, or can these be opened up and repaired?



Attachments
__________________
65 Laurentian post, 67 Grande Parisienne 4 door HT. 
 
Page 1 of 1  sorted by
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.