Pre 1958 Canadian Pontiac Power Train Tech Forum

fink · fink

I took the car out for a test drive and it's nice and quiet the only issue is that there is a slow leak at the front end of the countershaft where it has the step machined into it. The shaft hasn't spun at all and it's not leaking at the rear so I cleaned it off and applied ultra rtv black silicon over the end of th...

fink · fink

i'm trying to figure out what size the clutch is in my 1954 pontiac pathfinder. it has the flat six 239. i drive the car every day to work and i would like to have the stuff ready to install when the snow flys. the only problem is that i cannot find any info on the clutch o.d. its not the typical chevy size of 9...

fink · fink

hey my nos pressure plate isnt x marked or anything. my other two old plates have marks by the bolt heads one says G the other has an S. the flywheel has nothing at all and i think its an aftermarket flywheel that will accept two different pressure plates because it has two sets of holes. how do i make sure th...

4SPEED427 · 4SPEED427

I'll readily admit the 54 and down Pontiacs are somewhat foreign to me. However, I'd like to help someone out needing a part number for fuel pump on a 52. All I can tell you is I think he said it's a Fleetleader. My parts book has this: 1537342 1949-52/20-22-25 TYPE 7342 5592657 1951-52/27, 1953-54/ALL T...

adam · adam

hey everyone, I have finally found an original shop manual for my 55 pathfinder, it has the 261ci with the old slushbox behind it. this is the first 2 speed powerglide equipped car that ive owned (all others hav small blocks with overdrives!! lol) and as I was reading through the manual I noticed that in...

B-52 · B-52

I lost some info I had saved on my computer, so now I'm wondering the oil capacity for the flat six engine and I do have the external oil filter. Do I add one extra liter of oil because of the filter? Won't it read "over filled" on the dipstick? I'm at about full right now with 5 liters of oil but I'm...

1952pontiac · 1952pontiac

Hi Can somebody help me whit this id like to know how where the two hose from the filter hook up to on my 239 engine.

hwscowboy · hwscowboy

does anybody have a valid part number for the waterpump on my 54 pontiac 239 engine.I seem to have a leak suddenly.I found a couple on ebay but would like to try and find one locally first.The number on the ebay ones did not seem to cross.

1-bad-57 · 1-bad-57

Hi Guys I have a 283 complete motor made in Canada. The block number is 3731548 the stamped number is 9v79305. Heads are 3731554 hc and the crank is 3735236 Any help would be great Thanks, Joe

1952pontiac · 1952pontiac

I'd like to know if the rear end from a 53 or 54 would fit on my 52 fleetleader deluxe or if i have to midified someting. my 52 is 4.11 ratio and the 53 is 3.70 ratio -- Edited by 1952pontiac on Sunday 8th of July 2012 12:17:44 PM

Harley61 · Harley61

I have a 52 Fleetleader with the straight 6, when it is cold it fires right up and runs great, after about 30 to 45 minutes when you accelerate it hesitates and gets a little "bucky" if you shut it down it will not restart until it cools off. A friend suggested starting with the condenser and che...

Pheadrus · Pheadrus

Hi Guys I'm looking for some help with the engine code for my 57. I know a "W" designates a 6 cylinder but I haven't found any info on my engine code. I know it's a V-8 but not which 283 it has or what the "9" represents. Any help would be appreciated. Thanks, Steve.

50sedandelivery · 50sedandelivery

The OEM carb for the 239 c.i. 6 cyl. is listed as a Carter WA-1 717S single barrel. I have a manifold assembly that has a Carter WCD 2-barrel that bolts right on. I am installing the Hi-Compression head on the rebuild and wonder if there is any reason not to use the 2- barrel?

willismcbillio · willismcbillio

So heres the story: previous owner of my 56 Laurentian swapped out the front seat for 2 buckets, put in a floor shifter and pulled the shift handle off of the column. The floor shifter is similar to a hurst promatic shifter with no plastic console around it, connected to a TH350. As of now I have no gear ind...

Christopher Lang · Christopher Lang

So, today while under my car, I noticed that my rear motor mounts are in dire shape, in fact, on the passenger side, there was no rubber left! I notice that they look much different than the ones listed for sale on ebay. Is there a difference between the american motor mounts and the Canadian? What have...

t-bucket · t-bucket

good morning gentlemen I have a predicament I'm sure more than one person has encountered before. I put a small block 350 into my 55 pontiac this winter and the water temperature sender unit won't reach to the front of the block where the sender should plug in. If possible I would like to use my original...

Christopher Lang · Christopher Lang

So, I know that the Canuck Pontiacs all (nearly all) had the mighty 239. My understanding is that they also had power glide, or hyrdamatic transmitions. Or the three on the tree. Now, I've also seen quite a number of 216 and 235 Chev engines in the Canadaian cars. Do the Stovebolts just bolt right in...

50sedandelivery · 50sedandelivery

Just got the machined block back from the shop (after many months of threatening phone messages to get it done) and I'm starting the assembly. The shop installed the new valves and guides. I asked how I would then get the lifters and cam back in and he replied "from the bottom". I have now rein...

Rick65Cat · Rick65Cat

Hi, I just joined this forum to ask a question on a car I'm interested in buying. Theres not many forums out there that dedicate themselves to pre 60s pontiacs. Its a `54 Pontiac, 32,000 original miles. But I'm unsure if its a Canadian or American model. All I know is thats its a "straight 8"...

northern56 · northern56

Hello, I found this air cleaner in the trunk of a 56 chev I'm parting out. I'm hoping someone here can tell me what it's for. Thanks for your help. Larry.

Topic		Started By	Replies	Views	Last Post
	Leaking around countershaft (Preview) I took the car out for a test drive and it's nice and quiet the only issue is that there is a slow leak at the front end of the countershaft where it has the step machined into it. The shaft hasn't spun at all and it's not leaking at the rear so I cleaned it off and applied ultra rtv black silicon over the end of th...	fink	0	1144	Nov 26, 2012 by fink
	what clutch should i be shopping for? help (Preview) i'm trying to figure out what size the clutch is in my 1954 pontiac pathfinder. it has the flat six 239. i drive the car every day to work and i would like to have the stuff ready to install when the snow flys. the only problem is that i cannot find any info on the clutch o.d. its not the typical chevy size of 9...	fink	22	2622	Nov 25, 2012 by fink
	new pressure plate has no x mark (Preview) hey my nos pressure plate isnt x marked or anything. my other two old plates have marks by the bolt heads one says G the other has an S. the flywheel has nothing at all and i think its an aftermarket flywheel that will accept two different pressure plates because it has two sets of holes. how do i make sure th...	fink	4	1257	Nov 14, 2012 by fink
	52 Fuel Pump Help (Preview) I'll readily admit the 54 and down Pontiacs are somewhat foreign to me. However, I'd like to help someone out needing a part number for fuel pump on a 52. All I can tell you is I think he said it's a Fleetleader. My parts book has this: 1537342 1949-52/20-22-25 TYPE 7342 5592657 1951-52/27, 1953-54/ALL T...	4SPEED427	5	1295	Oct 24, 2012 by 4SPEED427
	type of fluid for the 55 powerglide?? (Preview) hey everyone, I have finally found an original shop manual for my 55 pathfinder, it has the 261ci with the old slushbox behind it. this is the first 2 speed powerglide equipped car that ive owned (all others hav small blocks with overdrives!! lol) and as I was reading through the manual I noticed that in...	adam	2	1412	Oct 15, 2012 by 427carl
	Someone must have the answer!!!! (Preview) I lost some info I had saved on my computer, so now I'm wondering the oil capacity for the flat six engine and I do have the external oil filter. Do I add one extra liter of oil because of the filter? Won't it read "over filled" on the dipstick? I'm at about full right now with 5 liters of oil but I'm...	B-52	4	1929	Sep 12, 2012 by B-52
	oil filter on 239 engine (Preview) Hi Can somebody help me whit this id like to know how where the two hose from the filter hook up to on my 239 engine.	1952pontiac	5	1312	Jul 18, 2012 by B-52

	1954 pontiac pathfinder waterpump (Preview) does anybody have a valid part number for the waterpump on my 54 pontiac 239 engine.I seem to have a leak suddenly.I found a couple on ebay but would like to try and find one locally first.The number on the ebay ones did not seem to cross.	hwscowboy	2	1231	Jul 13, 2012 by Fitz
	Looking to decode a 283 motor (Preview) Hi Guys I have a 283 complete motor made in Canada. The block number is 3731548 the stamped number is 9v79305. Heads are 3731554 hc and the crank is 3735236 Any help would be great Thanks, Joe	1-bad-57	8	1316	Jul 12, 2012 by T37MAN
	1952 fleetleader deluxe (Preview) I'd like to know if the rear end from a 53 or 54 would fit on my 52 fleetleader deluxe or if i have to midified someting. my 52 is 4.11 ratio and the 53 is 3.70 ratio -- Edited by 1952pontiac on Sunday 8th of July 2012 12:17:44 PM	1952pontiac	2	838	Jul 9, 2012 by 1952pontiac
	Question on 52 Fleetleader ignition (Preview) I have a 52 Fleetleader with the straight 6, when it is cold it fires right up and runs great, after about 30 to 45 minutes when you accelerate it hesitates and gets a little "bucky" if you shut it down it will not restart until it cools off. A friend suggested starting with the condenser and che...	Harley61	7	1583	Jun 13, 2012 by B-52
	1957 engine decode?? Engine - 9V76399 (Preview) Hi Guys I'm looking for some help with the engine code for my 57. I know a "W" designates a 6 cylinder but I haven't found any info on my engine code. I know it's a V-8 but not which 283 it has or what the "9" represents. Any help would be appreciated. Thanks, Steve.	Pheadrus	2	1110	Jun 10, 2012 by Pheadrus
	CARBURETOR CONFUSION carb 239 gasoline performance (Preview) The OEM carb for the 239 c.i. 6 cyl. is listed as a Carter WA-1 717S single barrel. I have a manifold assembly that has a Carter WCD 2-barrel that bolts right on. I am installing the Hi-Compression head on the rebuild and wonder if there is any reason not to use the 2- barrel?	50sedandelivery	2	1036	Jun 1, 2012 by 50sedandelivery
	Possible to attach original column gear selector/indicator with floor shifter (Preview) So heres the story: previous owner of my 56 Laurentian swapped out the front seat for 2 buckets, put in a floor shifter and pulled the shift handle off of the column. The floor shifter is similar to a hurst promatic shifter with no plastic console around it, connected to a TH350. As of now I have no gear ind...	willismcbillio	7	1505	May 31, 2012 by davelacourse

	1949 239 Six Rear motor mounts (Preview) So, today while under my car, I noticed that my rear motor mounts are in dire shape, in fact, on the passenger side, there was no rubber left! I notice that they look much different than the ones listed for sale on ebay. Is there a difference between the american motor mounts and the Canadian? What have...	Christopher Lang	10	2073	Apr 19, 2012 by 50sedandelivery
	water temp senders (Preview) good morning gentlemen I have a predicament I'm sure more than one person has encountered before. I put a small block 350 into my 55 pontiac this winter and the water temperature sender unit won't reach to the front of the block where the sender should plug in. If possible I would like to use my original...	t-bucket	8	1112	Feb 4, 2012 by davelacourse
	Canuck Vs. USA Flathead bell-housings and transmissions and such. (Preview) So, I know that the Canuck Pontiacs all (nearly all) had the mighty 239. My understanding is that they also had power glide, or hyrdamatic transmitions. Or the three on the tree. Now, I've also seen quite a number of 216 and 235 Chev engines in the Canadaian cars. Do the Stovebolts just bolt right in...	Christopher Lang	1	1133	Jan 25, 2012 by Fitz
	239 CAMSHAFT INSTALL ISSUES valves engine assembly camshaft valve lifters (Preview) Just got the machined block back from the shop (after many months of threatening phone messages to get it done) and I'm starting the assembly. The shop installed the new valves and guides. I asked how I would then get the lifters and cam back in and he replied "from the bottom". I have now rein...	50sedandelivery	6	1208	Jan 19, 2012 by 50sedandelivery
	New guy Newbie question ( 1 2 ) (Preview) Hi, I just joined this forum to ask a question on a car I'm interested in buying. Theres not many forums out there that dedicate themselves to pre 60s pontiacs. Its a `54 Pontiac, 32,000 original miles. But I'm unsure if its a Canadian or American model. All I know is thats its a "straight 8"...	Rick65Cat	27	4478	Nov 13, 2011 by Captain Beaumont
	air cleaner (Preview) Hello, I found this air cleaner in the trunk of a 56 chev I'm parting out. I'm hoping someone here can tell me what it's for. Thanks for your help. Larry.	northern56	2	969	Nov 12, 2011 by northern56
«First < 1 … 4 5 6 7 8 … 10 > Last» \| Page of 10 sorted by