Pre 1958 Canadian Pontiac Chassis Forum

brokeassbuilder · brokeassbuilder

im looking at putting a 1939 pontiac 2drcoupe body on a 41 pontiac chassis will it fit or will it haveto be cutdown and remounted ?

Laurentian 57 · Laurentian 57

Bonjour! The body brackets of my '57 are too rusted for making their job. Have I to manufacture it or can I find that new ?

Laurentian 57 · Laurentian 57

Hi, I have a problem with a piece of my right steering but I don't know the english name of it... You see on the picture, the axe is twisted because the rubber is older than me. I need to find that for the both ends and the both sides.

sixtywagon · sixtywagon

A friend of mine found a 58 in a field in Northern Alberta that he may pick up(just for parts, he's a chevy guy) But he says it has factory air suspension in it, like some 58 chevs were ordered with. Anyone ever hear of such a critter? Or know how rare it might be? I haven't seen the car, but he says its prett...

welldunn · welldunn

Hey Guys, i've got the whole front end out of the car now , how do i get the coil springs out? I have 2 spring compressors here and either will work. There has to be a technique to this if anyone has any info please let me know. thanks

welldunn · welldunn

I know i have something bent in my front end but i can't tell exactly what piece i need to get or maybe i need to get it all. This car must have hit something before and the idler and tie rods are a little out of whack because the part that is secured to the front axle is pushing up into the oil pan. If anyone has a...

davelacourse · davelacourse

The factory welded a bracket assembly to the frame near the cowl to support the column shift linkage: I want to remove this bracket, because (a) it is not needed since I am using a floor shift and (b) to clean up unnecessary clutter in the engine compartment (which will be much more croweded with the big b...

brad2v · brad2v

Diving right in with a question, I did do an intro though. Correct me if I'm wrong, but is the chassis and it's components (suspension, diff, etc) all Chevrolet? Ie, can I order ball joints, tie rods, diff bearings and the like for a Chev?

welldunn · welldunn

my car has 14's on it and it's a 1953 pontiac is that correct ? i was told by one guy that he thinks it should be 15's. thanks

pontiacman · pontiacman

Has anyone ever replace the front drum setup to a disk on a 58 Laurention the the rim off set change

wwdaze · wwdaze

Hello: I am looking for a steering box for my 1952 fleetleader special, 6 cyl. My mechanic thinks the steering and front end are chevrolet as they do not match the car manual for Pontiac. Any ideas?? I can buy a rebuild kit but would prefer to buy one already done. Thanks for your help in the past. B...

Laurentian 57 · Laurentian 57

Hello! Is there anyone knowing the references for me to buy four new wheel cylinders for my 57 Laurentian 6 x 261 i.c. Pierre

welldunn · welldunn

I can't find a power brake conversion kit for my car and all the kids at the speed-shops are useless unless it has a turbo. Is there another kind of car i can ask for parts for by chance? thanks guys

welldunn · welldunn

i'm having trouble finding how to route the front brakes lines , does anyone know if this early of a car has a proportioning valve? i can see where the back brake lines ru nto the front but i cannot see the front lines and there is no junction block in the front and i think there should be right? Any help is mu...

Chief 53 · Chief 53

Just wondering if anyone has done a conversion to tapered front wheel bearings. This conversion kit replaces the same wheel bearings listed for my 53 http://www.dreamershotrods.com/cpp-4759rbk-u.aspx

57Pontiac · 57Pontiac

Sorry to be a pain guys, but I need help with another bracket. I thought I had labelled everything correctly and took enough pictures, but appenrently not! I suspect this goes either on the frame or transmission, but no clue where. Thanks again

57Pontiac · 57Pontiac

Hi guys, I am unable to determine where this part goes. I looked in my documentation and the tons of pictures I took when dismanteling my car and no trace of this part... it may come from one of 2 other cars I parted out, but still I have no clue where it goes If anyone has any idea..please let me know Thanks!...

57Pontiac · 57Pontiac

Hi guys, I'm trying to figure out if I should restore the original drums brakes on my 1957 Laurentian or buy a complete disk brakes kit. I imagine it would be probably a lot cheaper to restore my original brakes, but security-wise is it safer to go with disk brake? Anyone has ever installed a disk kit? Do...

brad · brad

I have a 65 2 door beaumont, I also have a 66 4 door chevelle are the frames the same - interchangeable? -- Edited by brad on Wednesday 17th of March 2010 07:33:57 PM

davelacourse · davelacourse

Well I drove to the alignment shop, and he put the 56 with all new/rebuilt front suspension on the fancy computerized/laser-guided machine, and ... cannot get anywhere close to the factory specified 1 degree postive caster, and cannot get any positive camber either (toe-in of course is not a proble...

Topic		Started By	Replies	Views	Last Post
	1939 -41 chassis is there a large diffrence? (Preview) im looking at putting a 1939 pontiac 2drcoupe body on a 41 pontiac chassis will it fit or will it haveto be cutdown and remounted ?	brokeassbuilder	1	2483	Dec 13, 2010 by 427carl
	Body brackets (Preview) Bonjour! The body brackets of my '57 are too rusted for making their job. Have I to manufacture it or can I find that new ?	Laurentian 57	8	2458	Oct 15, 2010 by Fitz
	steering of my 57 Laurentian (Preview) Hi, I have a problem with a piece of my right steering but I don't know the english name of it... You see on the picture, the axe is twisted because the rubber is older than me. I need to find that for the both ends and the both sides.	Laurentian 57	5	1629	Sep 29, 2010 by Laurentian 57
	58 Pontiac w/factory air suspension? (Preview) A friend of mine found a 58 in a field in Northern Alberta that he may pick up(just for parts, he's a chevy guy) But he says it has factory air suspension in it, like some 58 chevs were ordered with. Anyone ever hear of such a critter? Or know how rare it might be? I haven't seen the car, but he says its prett...	sixtywagon	11	4662	Aug 19, 2010 by cheetah 427
	'53 Pontiac Coil Spring Removal? (Preview) Hey Guys, i've got the whole front end out of the car now , how do i get the coil springs out? I have 2 spring compressors here and either will work. There has to be a technique to this if anyone has any info please let me know. thanks	welldunn	9	1851	Aug 2, 2010 by welldunn
	Which Part is Bent? (Preview) I know i have something bent in my front end but i can't tell exactly what piece i need to get or maybe i need to get it all. This car must have hit something before and the idler and tie rods are a little out of whack because the part that is secured to the front axle is pushing up into the oil pan. If anyone has a...	welldunn	1	1642	Jul 19, 2010 by Fitz
	What is the best way to remove unwanted frame bracket? - UPDATE (Preview) The factory welded a bracket assembly to the frame near the cowl to support the column shift linkage: I want to remove this bracket, because (a) it is not needed since I am using a floor shift and (b) to clean up unnecessary clutter in the engine compartment (which will be much more croweded with the big b...	davelacourse	21	2366	Jul 14, 2010 by 4SPEED427
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
	'57 Pontiac/'57 Chev chassis parts interchangablity? (Preview) Diving right in with a question, I did do an intro though. Correct me if I'm wrong, but is the chassis and it's components (suspension, diff, etc) all Chevrolet? Ie, can I order ball joints, tie rods, diff bearings and the like for a Chev?	brad2v	5	2105	Jun 7, 2010 by brad2v
	early 50's pontiac Factory Tire Size (Preview) my car has 14's on it and it's a 1953 pontiac is that correct ? i was told by one guy that he thinks it should be 15's. thanks	welldunn	6	3398	Jun 3, 2010 by davelacourse
	disc brake kit (Preview) Has anyone ever replace the front drum setup to a disk on a 58 Laurention the the rim off set change	pontiacman	1	1456	May 25, 2010 by davelacourse
	steering box (Preview) Hello: I am looking for a steering box for my 1952 fleetleader special, 6 cyl. My mechanic thinks the steering and front end are chevrolet as they do not match the car manual for Pontiac. Any ideas?? I can buy a rebuild kit but would prefer to buy one already done. Thanks for your help in the past. B...	wwdaze	3	1656	May 13, 2010 by Fitz
	Wheel cylinders (Preview) Hello! Is there anyone knowing the references for me to buy four new wheel cylinders for my 57 Laurentian 6 x 261 i.c. Pierre	Laurentian 57	3	2333	May 10, 2010 by 67Poncho
	Any Similarities from a 53 Pontiac to 55-57 Chev's (Preview) I can't find a power brake conversion kit for my car and all the kids at the speed-shops are useless unless it has a turbo. Is there another kind of car i can ask for parts for by chance? thanks guys	welldunn	10	1701	May 5, 2010 by Fitz
	53' Front Brake Lines (Preview) i'm having trouble finding how to route the front brakes lines , does anyone know if this early of a car has a proportioning valve? i can see where the back brake lines ru nto the front but i cannot see the front lines and there is no junction block in the front and i think there should be right? Any help is mu...	welldunn	1	1258	Apr 29, 2010 by bob53
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
	53 Front wheel bearings (Preview) Just wondering if anyone has done a conversion to tapered front wheel bearings. This conversion kit replaces the same wheel bearings listed for my 53 http://www.dreamershotrods.com/cpp-4759rbk-u.aspx	Chief 53	0	1202	Apr 26, 2010 by Chief 53
	Need help identify another bracket (Preview) Sorry to be a pain guys, but I need help with another bracket. I thought I had labelled everything correctly and took enough pictures, but appenrently not! I suspect this goes either on the frame or transmission, but no clue where. Thanks again	57Pontiac	3	2045	Apr 24, 2010 by davelacourse
	Need help to identify this 1957 part!! (Preview) Hi guys, I am unable to determine where this part goes. I looked in my documentation and the tons of pictures I took when dismanteling my car and no trace of this part... it may come from one of 2 other cars I parted out, but still I have no clue where it goes If anyone has any idea..please let me know Thanks!...	57Pontiac	5	1378	Apr 18, 2010 by 57Pontiac
	1957 Original Brakes or Disk brake kit??? (Preview) Hi guys, I'm trying to figure out if I should restore the original drums brakes on my 1957 Laurentian or buy a complete disk brakes kit. I imagine it would be probably a lot cheaper to restore my original brakes, but security-wise is it safer to go with disk brake? Anyone has ever installed a disk kit? Do...	57Pontiac	6	1919	Apr 10, 2010 by dualquadpete
	1965 and 66 frames (Preview) I have a 65 2 door beaumont, I also have a 66 4 door chevelle are the frames the same - interchangeable? -- Edited by brad on Wednesday 17th of March 2010 07:33:57 PM	brad	5	1943	Mar 21, 2010 by rabbit64cs
	Upper control arms - more caster? ( 1 2 ) What should I do? (Preview) Well I drove to the alignment shop, and he put the 56 with all new/rebuilt front suspension on the fancy computerized/laser-guided machine, and ... cannot get anywhere close to the factory specified 1 degree postive caster, and cannot get any positive camber either (toe-in of course is not a proble...	davelacourse	29	4124	Feb 7, 2010 by davelacourse
«First < 1 2 3 4 5 > Last» \| Page of 5 sorted by