Enjoy 5% OFF at VEVOR Canada! and Support Canadian Poncho at the Same Time!
Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: trans safety switch rod


Uber Guru

Status: Offline
Posts: 3025
Date:
trans safety switch rod


does anyone have this part ??
It is the small rod that goes from the trans linkage to the neutral safety switch
mine is broken off at the threads and missing the swivle part. right hand
side of pic
and part #3 on drawing..

thanks..


Attachments
__________________

Surrey BC

1963 Acadian Beaumont Sport Deluxe
http://www.63acadian.com/



Uber Guru

Status: Offline
Posts: 3025
Date:

1/2 way there, i found a part to take the place of the missing Swivle.
it is called a throttle ball joint from PAPCO (10-32 stock # 262-203)
the only problem was the stud on the ball joint was a 10-32 and the original hole is for a stud the size of an 8-32. so i ground off the threads and rethreaded it to an 8-32, now it fits in the hole
like a glove and with it being held on with a nut instead of a clip it will have very little play.
Now i just have to weld a new threaded tail in 10-32 to the shaft and i should be ready to go.

throttle ball joint_(1024_x_768).jpg

broken_(1024_x_768).jpg


__________________

Surrey BC

1963 Acadian Beaumont Sport Deluxe
http://www.63acadian.com/

Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


A Poncho Legend!

Status: Offline
Posts: 20744
Date:

Glad you found a solution ... there is always a way!

__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.



Uber Guru

Status: Offline
Posts: 3025
Date:

well it is repaired, now to see if i can install it without dropping the trans....
had to remove threads from ball joint and re-tap to 8/32 so it would fit through hole in bracket.
if this works i am going to make a complete new one with a larger rod so i can put a swivel on both ends.


throttle ball joint_(1024_x_768).jpg

new rod 1 with measurements_(1024_x_768) (2).jpg




-- Edited by Lefty on Monday 31st of January 2011 06:33:37 PM

__________________

Surrey BC

1963 Acadian Beaumont Sport Deluxe
http://www.63acadian.com/



Uber Guru

Status: Offline
Posts: 3025
Date:

Repair so far..
works but i will have to cut the end again and weld on a new 10/32 bolt.
As you car see im right at the end of the treads and i need to come back and 8th to line up with the black lines.
(tape will be removed after it works)
found a NOS switch but they want $500 !! i will repair this or live without...


neutral safety Sw 2cropped_(1024_x_768).jpg

__________________

Surrey BC

1963 Acadian Beaumont Sport Deluxe
http://www.63acadian.com/



A Poncho Legend!

Status: Offline
Posts: 20744
Date:

$500 for a switch, and $300.00 for the wiring ... OUCH!

__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.



Uber Guru

Status: Offline
Posts: 3025
Date:
RE:


Managed to repair a Sw i got from Menno...
Finally have a car that starts only in park and neutral!
and the brake light power goes to the trunk.
Next i just have to fix the lights themselves
Thanks Menno..


__________________

Surrey BC

1963 Acadian Beaumont Sport Deluxe
http://www.63acadian.com/

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.