Enjoy 5% OFF at VEVOR Canada! and Support Canadian Poncho at the Same Time!
Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: ignition


Addicted!

Status: Offline
Posts: 150
Date:
ignition


Hello all, got it ready to start today and it turns over but no fire. cleaned points tried again, same thing no fire. should i just swap out the cap and rotor, points and condenser and new wires and see what happens? Also i may have put the rotor on backwards, how do i tell? i know i should have taken a pic before removing, oh well eh?



__________________
dboode


A Poncho Legend!

Status: Offline
Posts: 50217
Date:

Try a voltmeter at the coil and see if you have at least 7-8 volts to it with the key on. During cranking it should have pretty well 12 volts to it.

You shouldn't be able to put the rotor on backwards. It should have one square tab on the bottom and one round tab on the bottom so that it is keyed to only go one way on to the distributor.



__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)

Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons


Addicted!

Status: Offline
Posts: 150
Date:

whew, thanks for that, i will test the coil tomorrow, again thank you

__________________
dboode


Canadian Poncho Superstar!

Status: Offline
Posts: 7788
Date:

The rotor will only go on one way. Have you checked for spark? Is the distributor cap seated properly?

__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop

 

 



Addicted!

Status: Offline
Posts: 150
Date:

I will test coil in the morning and get wife to watch for spark, im pretty sure the cap is on right but that's worth checking again
Thanks

__________________
dboode


Guru

Status: Offline
Posts: 926
Date:

4SPEED427 wrote:

Try a voltmeter at the coil and see if you have at least 7-8 volts to it with the key on. During cranking it should have pretty well 12 volts to it.

 This is likely the issue, it seems common that the IGN switch has a dead or weak spot right between the crank and run position. May have to run a separate wire.



-- Edited by 1965CS on Wednesday 24th of February 2021 01:59:52 PM

__________________

65 Custom Sport Convertible

Southern Alberta



A Poncho Legend!

Status: Offline
Posts: 50217
Date:

1965CS wrote:
4SPEED427 wrote:

Try a voltmeter at the coil and see if you have at least 7-8 volts to it with the key on. During cranking it should have pretty well 12 volts to it.

 This is likely the issue, it seems common that the IGN switch has a dead or weak spot right between the crank and run position. May have to run a separate wire.



-- Edited by 1965CS on Wednesday 24th of February 2021 01:59:52 PM


 Yes for some reason the old vehicles with the in-dash ignition switch seem to be prone to that exact problem you describe. I've seen a number of times where the guys say they were able to keep the vehicle running by holding the key in just the right place. I'm betting if a guy could get the ignition switch apart he could clean up the terminals and make it work properly again. I'm not sure how successful an attempt at taking it apart would be.



__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.