Be sure to visit The Canadian Poncho Swag Store

4SPEED427 · 4SPEED427

There was a thread with discussion on where to locate emblems on a particular vehicle. Todd has suggested that there be a section in each of the separate forums for particular models, so I will start one in each of those sections. If you are able to assist with specs on body emblem placement for the model...

SNR Pontiac · SNR Pontiac

Hey guys, just looking at a 64 Convertible. Its going to need rear quarters, but does anyone know if the convertible is different from the 2 door?? Thanks

64PARCONUK · 64PARCONUK

I need rear quarter panels and Nor/Am seem to be the only source, but they never answer the phone only offer to phone back. Since I'm often in a different day let alone in a different time zone and they would be phoning international, the chances of my phone ringing when I'm awake or even near it are very...

pontiax · pontiax

$50 for the pair plus shipping. Half to C.P. driver quality, no cracks just some light pitting. Lenses are toast. -- Edited by pontiax on Thursday 21st of June 2018 11:17:33 AM

Eggwelder · Eggwelder

Didn`t take as may pics as i should have. Drivers side fender. Above the headlights is aluminum tape covered in body filler. Above the trim on the lower front in front of the wheel well is the same, as in the back lower corner in front of the door. The brace is rusted thru for the lowest 4 inches, and the nut t...

Glenn Musgrave · Glenn Musgrave

Thought I'd start a new topic for this incase anyone wants to follow along and to help me find previous post on the topic. The main floor pan has been in for a while, it was blasted, treated to 2 coats of POR-15 inside and out and the underside then had 2 finish coats of paint to match the body. Pretty sure I...

Eggwelder · Eggwelder

My hood has bad rust along the front end. There is quite a bit of rust between the hood brace and the hood itself. I took the plunge today and drilled out almost 100 spot welds and popped the two apart. Have one side of the hood patched now and a good start on replacing the leading edge of the brace. When all th...

top down · top down

I'm in the process of replacing/building the floor sections on the 58 Pathfinder Sedan Delivery. I am planning on leaving the bench seat, the only seat in this beast. The question is, what have others done as far as installing seat belts for these older cars. I would think lap belts woul...

4SPEED427 · 4SPEED427

I emailed this pic to Pontiax knowing he knows 64's and that's what I thought they might be. He says no. Maybe 63?

pontiax · pontiax

I found a 4 1/4 round mirror glass on line. American made BURCO 3027 . Its a tinted grey convex mirror that matches the OPGI tint of my drivers side. But WOW what a difference in view. I see the quarter panel and 1 1/2 lanes beside me without distortion. Pictured is the style of mirror it fits. I believe oth...

top down · top down

I am looking for the weatherstrip for a 58 Sedan Delivery Rear door weatherstrip, one pcs door. any idea where I may find this. Thanks

66 Grande guy · 66 Grande guy

Hi guys a friend of a friend has an American 63 Pontiac up here in the frozen north and was wondering if Canadian Pontiac front fenders are the same. I think not but I thought I'd check with the collective wisdom here.

Casey Jones · Casey Jones

Hi! I'm looking for 1964 Pontiac Parisienne convertible reproduction quarter panels. Is it the same as Bonneville or Catalina? I know that Bonneville and Catalina are longer than the Parisienne. Thanks!

otus · otus

A lot of the trim on my car has gold finish on it as I am sure many are aware. Does anyone know how this was done originally ? For some reason someone removed the gold and the white (and the black on my headlight bezels) off off my emblems. I see pics online of restorations where the gold lettering etc look lik...

Bill shuba · Bill shuba

Hi all I am seriously looking at a 64 Strato Chief Wagon,its sitting in a field and by the pics of the car and how high the grass is its hard to see any of the first foot of the car,the rest looks in pretty good shape,327 3 speed not running...question is I am worryied about frame,floors,rust along the botto...

-Robert M- · -Robert M-

Glenn Musgrave · Glenn Musgrave

Hi everyone, I'm new to the site and hope to draw on some of your expertise. We are doing a frame restoration on a '62 Parisienne 2 Dr HT. Does anyone know if Chevy rear outter wheel wells will fit? Mine are repairable but I would go new if it isn't too much hastle. Also looking to source exterior molding cli...

Pontiackidontario · Pontiackidontario

I need floor pans for a 2 door post 61 pontiac laurentian I have not found much online but I've been told that other chevy pans might fit like a chevy impala?

Pontiackidontario · Pontiackidontario

Was wondering if there is a source for the rear glass seal for a canopy roof ?

otus · otus

I know I'm the dumb one here but are 64 Custom Sport grills a stand alone item?? I see that they look like 63 grills but not quite. As I surf around I notice all kinds of ads with all kinds of conflicting descriptions and pics regarding "Custom Sport" in 1964. I am referring to Canadian models....For some r...

Topic		Started By	Replies	Views	Last Post
	STICKY: Emblem Placement Dimensions (Preview) There was a thread with discussion on where to locate emblems on a particular vehicle. Todd has suggested that there be a section in each of the separate forums for particular models, so I will start one in each of those sections. If you are able to assist with specs on body emblem placement for the model...	4SPEED427	9	2641	Nov 24, 2018 by Pontiacanada
	Need help....are the 64 Parisienne convertible and 2 dr rear quarters the same?? (Preview) Hey guys, just looking at a 64 Convertible. Its going to need rear quarters, but does anyone know if the convertible is different from the 2 door?? Thanks	SNR Pontiac	4	204	13 days ago by NOS
	Contacting Nor/AM (Preview) I need rear quarter panels and Nor/Am seem to be the only source, but they never answer the phone only offer to phone back. Since I'm often in a different day let alone in a different time zone and they would be phoning international, the chances of my phone ringing when I'm awake or even near it are very...	64PARCONUK	2	641	February 1st by a421cat
	1963 full size tail light housings for sale. (Preview) $50 for the pair plus shipping. Half to C.P. driver quality, no cracks just some light pitting. Lenses are toast. -- Edited by pontiax on Thursday 21st of June 2018 11:17:33 AM	pontiax	12	4705	Oct 25, 2022 by Ducklife
	1958 stratochief fender work (Preview) Didn`t take as may pics as i should have. Drivers side fender. Above the headlights is aluminum tape covered in body filler. Above the trim on the lower front in front of the wheel well is the same, as in the back lower corner in front of the door. The brace is rusted thru for the lowest 4 inches, and the nut t...	Eggwelder	11	1484	Jun 19, 2022 by Glenn Musgrave
	Glenn's 62 Parisienne Rebuild ( 1 2 3 ) (Preview) Thought I'd start a new topic for this incase anyone wants to follow along and to help me find previous post on the topic. The main floor pan has been in for a while, it was blasted, treated to 2 coats of POR-15 inside and out and the underside then had 2 finish coats of paint to match the body. Pretty sure I...	Glenn Musgrave	59	5968	Jun 19, 2022 by Glenn Musgrave
	1958 hood rebuild (Preview) My hood has bad rust along the front end. There is quite a bit of rust between the hood brace and the hood itself. I took the plunge today and drilled out almost 100 spot welds and popped the two apart. Have one side of the hood patched now and a good start on replacing the leading edge of the brace. When all th...	Eggwelder	6	1020	Dec 28, 2021 by Eggwelder

	Seat Belts (Preview) I'm in the process of replacing/building the floor sections on the 58 Pathfinder Sedan Delivery. I am planning on leaving the bench seat, the only seat in this beast. The question is, what have others done as far as installing seat belts for these older cars. I would think lap belts woul...	top down	5	1091	Nov 8, 2021 by top down
	Are these 63 grilles? (Discovered to be 1967 grilles!) (Preview) I emailed this pic to Pontiax knowing he knows 64's and that's what I thought they might be. He says no. Maybe 63?	4SPEED427	4	1963	Sep 2, 2021 by 4SPEED427
	Convex passenger mirror for Round GM style mirrors (Preview) I found a 4 1/4 round mirror glass on line. American made BURCO 3027 . Its a tinted grey convex mirror that matches the OPGI tint of my drivers side. But WOW what a difference in view. I see the quarter panel and 1 1/2 lanes beside me without distortion. Pictured is the style of mirror it fits. I believe oth...	pontiax	12	1238	Jun 18, 2021 by norontcan
	Door weatherstrips (Preview) I am looking for the weatherstrip for a 58 Sedan Delivery Rear door weatherstrip, one pcs door. any idea where I may find this. Thanks	top down	1	1088	Jun 4, 2021 by NOS
	1963 Pontiac front fenders (Preview) Hi guys a friend of a friend has an American 63 Pontiac up here in the frozen north and was wondering if Canadian Pontiac front fenders are the same. I think not but I thought I'd check with the collective wisdom here.	66 Grande guy	3	1189	Jan 28, 2021 by Prefectca
	1964 Pontiac Parisienne quarter panel (Preview) Hi! I'm looking for 1964 Pontiac Parisienne convertible reproduction quarter panels. Is it the same as Bonneville or Catalina? I know that Bonneville and Catalina are longer than the Parisienne. Thanks!	Casey Jones	15	1624	Jan 22, 2021 by a421cat
	gold trim (Preview) A lot of the trim on my car has gold finish on it as I am sure many are aware. Does anyone know how this was done originally ? For some reason someone removed the gold and the white (and the black on my headlight bezels) off off my emblems. I see pics online of restorations where the gold lettering etc look lik...	otus	0	1449	Jun 26, 2020 by otus

	64 wagon (Preview) Hi all I am seriously looking at a 64 Strato Chief Wagon,its sitting in a field and by the pics of the car and how high the grass is its hard to see any of the first foot of the car,the rest looks in pretty good shape,327 3 speed not running...question is I am worryied about frame,floors,rust along the botto...	Bill shuba	3	1801	Oct 29, 2019 by Bill shuba
	Manitoba Pontiac Body work underway (Preview)	-Robert M-	4	1769	Oct 26, 2019 by 4SPEED427
	Will Chevy Outter Wheel Wells Fit? (Preview) Hi everyone, I'm new to the site and hope to draw on some of your expertise. We are doing a frame restoration on a '62 Parisienne 2 Dr HT. Does anyone know if Chevy rear outter wheel wells will fit? Mine are repairable but I would go new if it isn't too much hastle. Also looking to source exterior molding cli...	Glenn Musgrave	15	2095	Oct 24, 2019 by Glenn Musgrave
	61 Pontiac laurentian floor (Preview) I need floor pans for a 2 door post 61 pontiac laurentian I have not found much online but I've been told that other chevy pans might fit like a chevy impala?	Pontiackidontario	6	2073	Oct 22, 2019 by otus
	1961 Pontiac laurentian canopy roof glass seal (Preview) Was wondering if there is a source for the rear glass seal for a canopy roof ?	Pontiackidontario	5	1632	Oct 9, 2019 by NOS
	64 Parisienne grills? (Preview) I know I'm the dumb one here but are 64 Custom Sport grills a stand alone item?? I see that they look like 63 grills but not quite. As I surf around I notice all kinds of ads with all kinds of conflicting descriptions and pics regarding "Custom Sport" in 1964. I am referring to Canadian models....For some r...	otus	4	2065	Aug 20, 2019 by Pontiacanada
1 2 3 … 10 > Last» \| Page of 10 sorted by